Read Sharp XE-A202 Service Manual online
XE-A202V
SPECIFICATIONS
– 2 –
The mode switch has these settings:
q
:
This mode locks all register operations. (AC power turns off.)
No change occurs to register data.
No change occurs to register data.
OP X/Z: To take individual clerk X or Z reports, and to take flash
reports.
It can be used to toggle receipt state “ON” and “OFF” by press-
ing he [RCPT/PO] key.
ing he [RCPT/PO] key.
REG:
For entering sales.
PGM:
To program various items.
p
:
Enters into the void mode. This mode allows correction after
finalizing a transaction.
finalizing a transaction.
MGR:
For manager’s entries. The manager can use this mode for an
override entry.
override entry.
X1/Z1: To take the X/Z report for various daily totals.
X2/Z2: To take the X/Z report for periodic (weekly or monthly) consoli-
dation.
5. DISPLAY
1) OPERATOR DISPLAY
Display device
: LED numeric display
Number of line
: 1 line
Number of positions : 10 positions numeric display
Color of display
: Yellow / Green
Character form
: 7 segment + DP
Character size
: Numeric 14.2 (H) x 7.9 (W) mm
Layout:
2) CUSTOMER DISPLAY
Display device
: LED
Number of line
: 1 line
Number of positions : 7 positions
Color of display
: Yellow / Green
Style
: Pop up type
Character form
: 7 segment + Dp
Character size
: 14.2mm (H) x 7.9mm (W)
Layout:
Amount: Appears in the far-right eight (max.) positions. When the
amount is negative, the minus symbol "-" appears before the
amount.
Number of repeats for repetitive registrations:
The number of repeats is displayed, starting at "2" and incre-
mental with each repeat. When you have registered ten times,
mental with each repeat. When you have registered ten times,
the display will show "0." (2
3
3 .... 9
3
0
3
1
3
2 ... )
Receipt function status:
The indicator "_" appears in the RCPT OFF position when the
receipt function is in the OFF status.
receipt function is in the OFF status.
Time:
Appears in the second to sixth positions (using 24-hour format)
in the OP X/Z, REG or MGR mode. In the REG or MGR mode,
press the [#/TM/ST] key to display the time.
■
■
■
■
Machine state symbols
:
Appears during programming.
:
Appears when an error is detected.
:
Appears when the subtotal is displayed or when the amount ten-
dered is smaller than the sales amount.
:
Appears when the [EX] key is pressed to calculate a subtotal in
foreign currency.
foreign currency.
:
Appears when a transaction is finalized by pressing the [TL/NS],
[CH1], [CH2], [CR1] or [CR2] key.
:
Appears when the change due amount is displayed.
: Appears in the far-left three positions at the timing of key entry
when the electronic journal (EJ) memory is full. (Depending on
programming.)
programming.)
:
Appears when the voltage of the installed batteries is under the
required level. You must replace with new ones within two days.
:
Appears when the batteries are not installed, or the installed bat-
teries are dead. You must replace with new ones immediately.
:
May appear right below the eighth and ninth places at the timing
of finalization of a transaction when the electronic journal (EJ)
of finalization of a transaction when the electronic journal (EJ)
memory is nearly full.
Also appears right below the tenth place when power save
mode is effective.
mode is effective.
: Appears when programmed date (and time) for EURO modifica-
tion operation is come.
:
Appears when the print roller arm is not locked.
:Appears when the paper is not set or out.
0 . 1 . 2 . 3 . 4 . 5 . 6 . 7 . 8 . 9 .
3 . 4 . 5 . 6 . 7 . 8 . 9 .
Operator display
Customer display (Pop-up type)
PLU/SUB
DEPT REPEAT
RCPT
OFF
NUMBER
SHIFT
DC
Clerk code
Click on the first or last page to see other XE-A202 service manuals if exist.