ER-A570 (serv.man8). ERA570 Programming Manual - Sharp ECR Service Manual (repair manual). Page 52

3. File creation terminates successfully and a request for floppy

disk replacement is made.

#0896 ∗Π Γ Μ ≤ ∗

JOB CODE/MODE TITLE

 

σενδ

 

              ερρορ 8

φ1200111. δατ       οκ

The TL key can be entered.

4. After the existing floppy disk, the CA key is entered.

Then the remaining data is successfully stored in another file
in the new disk.

 

#0896 ∗Π Γ Μ ≤ ∗ 

JOB CODE/MODE TITLE

 

σενδ 

 

              ερρορ 8 

φ1200111. δατ       οκ 

φ1200111. δατ       οκ 

 

DISPLAY FORMAT
 

Note 1: The table file (file No. 700) cannot extend over multi-

ple media (floppy disks).

Note 2: If the floppy disk contains any file that is the same in

file name as the file to be created in a file creation
step 2 or 4 above, "FILE NAME SEND?" appears on
the ECR display.
To create the file, it is necessary to enter the TL key;
and otherwise it is necessary to enter the  

⊗

 key.

Those file extending over multiple media (floppy disks) can
be received by performing the ordinary receive operation
(see 4-6)).

This function causes the ECR to receive file data from the ER-02FD.

The ECR can receive specified files from a floppy disk in the ER-
02FD connected to it when the above job is performed.
If any specified file is not present in the ECR, a "ENTRY ERROR"
error occurs.

PRINT FORMAT
When the send operation has successfully terminated:

#0895 ∗Π Γ Μ ≤ ∗

JOB CODE/MODE TITLE

 

ρεχει ϖε

 

φ1100111. δατ       οκ

When the send operation has been canceled:

#0898 ∗Π Γ Μ ≤ ∗ 

 

ρεχει ϖε 

 

φ1100111. δατ   ερρορ4 

ERROR4
(Specified file is not present.)

DISPLAY FORMAT
During a Receive operation

∗

If ECR memory space is full when ECR is receiving the data, a
"MEMORY FULL" error occurs. (The data received before the
"MEMORY FULL" error occurs is valid.)

PRINT FORMAT
When "MEMORY FULL" error occurs:

 

#0895 ∗Π Γ Μ ≤ ∗

JOB CODE/MODE TITLE

 

ρεχει ϖε

 

φ010ξξξξ. δατ       οκ

 

µεµορψ φυλλ

The presetting of stack files enables those files to be loaded and
dumped with a single job.
This presetting is of addition type. The following two kinds of preset-
ting are available.

PGM2 MODE

PGM2 MODE

PRINT FORMAT
When "MEMORY FULL" error occurs:

 

#0887 ∗Π Γ Μ ≤ ∗ 

JOB CODE/MODE TITLE

 

         φ1101111. δατ 

Stack file preset

         φ1201111. δατ 

         φ1301111. δατ 

φ1401111. δατ     −−−− 

Individual deletion of stack file

(FILE No.)

TL

898

X

(FILE No.)

ST

887

X

TL

X

TL

For individual deletion
atack files

For full deletion of atack files

(Up to 20 files can be preset)

(FILE No.)

ST

888

X

TL

X

TL

For individual deletion
atack files

For full deletion of atack files

(Up to 20 files can be preset)

 51 