Read Sharp DV-NC65H (serv.man13) Service Manual online
28
DV-NC65H/S
DV-NC70H
DV-NC70H
8-8. CHECKING AND ADJUSTMENT OF TAKE-
UP TORQUE IN FAST FORWARD MODE
• Remove the cassette housing control assembly.
• After short-circuiting between TP803 and TP802 pro-
• After short-circuiting between TP803 and TP802 pro-
vided at VCR Operation PWB, plug in the power cord.
• Setting
1. Set a torque gauge to zero on the scale. Place it on the
1. Set a torque gauge to zero on the scale. Place it on the
take-up reel disk.
2. Press the FF button.
3. To calculate the remaining capacity of the play back
3. To calculate the remaining capacity of the play back
mode, slowly rotate the supply reel disk, and then shift
it into the forward mode.
it into the forward mode.
• Checking
1. Turn the torque gauge slowly (one rotation every 2 to 3
1. Turn the torque gauge slowly (one rotation every 2 to 3
seconds) by hand in the CW direction.
2. Make sure that the indication of torque gauge is not less
than 25mN·m (255gf·cm).
Figure 8-7.
Torque gauge
25mN·m (255gf·cm)
or more
or more
The gauge is held at
its maximum value.
(Red mark)
its maximum value.
(Red mark)
Idler ass'y
• Adjustment
1. If the FF winding-up torque is less than the specified
1. If the FF winding-up torque is less than the specified
value, clean the capstan D.D. motor pulley, reel belt, and
limiter pulley with cleaning liquid, and check again.
limiter pulley with cleaning liquid, and check again.
2. If the torque is less than the set value, replace the reel
belt.
Notes:
1. Hold the torque gauge by hand so that it is not moved.
2. Do not keep the reel disk in lock state. Do not allow long-
1. Hold the torque gauge by hand so that it is not moved.
2. Do not keep the reel disk in lock state. Do not allow long-
time measurement.
CW
8-9. CHECKING AND ADJUSTMENT OF TAKE-
UP TORQUE IN REWIND MODE
• Remove the cassette housing control assembly.
• After short-circuiting between TP803 and TP802 pro-
• After short-circuiting between TP803 and TP802 pro-
vided at VCR Operation PWB, plug in the power cord.
• Setting
1. Set a torque gauge to zero on the scale. Place it on the
1. Set a torque gauge to zero on the scale. Place it on the
supply reel disk.
2. Press the rewind button.
3. To calculate the remaining capacity, slowly rotate the
3. To calculate the remaining capacity, slowly rotate the
take-up reel disk, and then shift it into the rewind mode.
• Checking
1. Turn the torque gauge slowly (one rotation every 2 to 3
1. Turn the torque gauge slowly (one rotation every 2 to 3
seconds) by hand in the CCW direction.
2. Make sure that the indication of torque gauge is not less
than 25mN·m (255gf·cm).
Figure 8-8
Torque gauge
25mN·m (255gf·cm)
or more
or more
Supply reel disk
Idler ass'y
The gauge is held at
its maximum value.
(Red mark)
its maximum value.
(Red mark)
• Adjustment
1. If the rewind winding-up torque is less than the specified
1. If the rewind winding-up torque is less than the specified
value, clean the capstan D.D. motor pulley, reel belt, and
limiter pulley with cleaning liquid, rewind again, and
check the winding-up torque.
limiter pulley with cleaning liquid, rewind again, and
check the winding-up torque.
2. If the winding-up torque is still out of range, replace the
reel belt.
Notes:
1. Hold the torque gauge by hand so that it is not moved.
2. Do not keep the reel disk in lock state. Do not allow long-
1. Hold the torque gauge by hand so that it is not moved.
2. Do not keep the reel disk in lock state. Do not allow long-
time measurement.
CCW
Click on the first or last page to see other DV-NC65H (serv.man13) service manuals if exist.