Read Sharp XL-HF202PH (serv.man5) User Guide / Operation Manual online
22
Troubleshooting chart (continued)
■
Factory reset, clearing all memory
1
Press the ON/STAND-BY button to turn the power on.
2
Press FUNCTION button (main unit) repeatedly or
AUDIO/LINE (INPUT) button (remote control) to enter
Audio In mode.
3
Press button (main unit) once.
4
Press and hold button (main unit) until “RESET” appears.
Caution:
This operation will erase all data stored in memory includ-
ing clock, timer settings and tuner preset.
■
Before transporting the unit
Remove all devices connected to the unit. Then, set the
unit to the power stand-by mode. Carrying the unit with
other devices left connected or discs left inside might dam-
age the unit.
■
Care of discs
Discs are fairly resistant to damage. However mistracking
can occur due to accumulation of dirt on the surface.
●
Do not mark on the non-label side of the disc from which
signals are read.
●
Keep your discs away from direct sunlight, heat, and
excessive moisture.
●
Always hold the discs by the edges. Fingerprints, dirt,
or water on the CDs can cause noise or mistracking.
Clean it with a soft, dry cloth, wiping straight out from the
centre, along the radius.
Maintenance
■
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted
soap solution, then with a dry cloth.
Caution:
Caution:
●
Do not use chemicals for cleaning (petrol, paint thin-
ner, etc.). It may damage the cabinet.
●
Do not apply oil to the inside of the unit. It may cause
malfunctions.
■
Cleaning the CD pickup lens
Poor performance during CD playback (skipping or jumping)
can be caused by a dirty or contaminated CD laser pick up
lens. If this happens then the use of a commercially available
CD lens cleaning disc may restore normal operation.
Contact your supplier or local CD software dealer to obtain
CD lens cleaning discs. Ensure all included instructions/
documentation are carefully followed.
Specifications
As part of our policy of continuous improvement, SHARP
reserves the right to make design and specification chang-
es for product improvement without prior notice. The per-
formance specification figures indicated are nominal val-
ues of production units. There may be some deviations
from these values in individual units.
■
General
Power source
AC 220 - 240 V ~ 50/60 Hz
Power
consumption
Power on: 52 W
Power stand-by: 0.4 W (*)
Dimensions
Width: 215 mm (8 - 1/2”)
Height: 96 mm (3 - 4/5”)
Depth: 335 mm (13 - 1/5”)
Weight
2.6 kg (5.7 lbs.)
Frequency band 2.400GHz - 2.480GHz
Compatible
Bluetooth Profile
A2DP (Advanced Audio Distribution
Profile), AVRCP (Audio/Video
Remote Control Profile)
Bluetooth 2.1 +EDR
( * ) This power consumption value is obtained when the demon-
stration mode is cancelled in the power stand-by mode. Re-
fer to page 4 to cancel the demonstration mode.
■
Amplifier
Output power
MPO: 100 W (50 W + 50 W)
(10% T.H.D.)
RMS: 100 W (50 W + 50 W)
(10% T.H.D.)
RMS: 66 W (33 W + 33 W)
(1% T.H.D.)
Output terminals Speakers: 4 ohms
20Hz - 20kHz
Subwoofer Pre-out (audio signal):
200 mV/10 k ohms at 70 Hz
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
Input terminals
Audio In (audio signal):
500 mV/47 k ohms
Line in (Analogue input):
500 mV/47 k ohms
Click on the first or last page to see other XL-HF202PH (serv.man5) service manuals if exist.