Read Sharp XL-DAB9H User Guide / Operation Manual online
05/7/12
XL-DAB9H(E)4.fm
31
TINSEA068SJZZ
XL-DAB9H
RDS Operatio
n
Using the Radio Data System (RDS) (continued)
To stop the ASPM operation before it is complete:
Press the ASPM button whilst it is scanning for stations.
The stations which are already stored in memory will be kept there.
Press the ASPM button whilst it is scanning for stations.
The stations which are already stored in memory will be kept there.
Notes:
z
If the same station is broadcasting on different frequencies, the
strongest frequency will be stored in memory.
strongest frequency will be stored in memory.
z
Any station which has the same frequency as one stored in mem-
ory will not be stored.
ory will not be stored.
z
If 40 stations have already been stored in memory, the scan will
be aborted. If you want to redo the ASPM operation, erase the
preset memory.
be aborted. If you want to redo the ASPM operation, erase the
preset memory.
z
If no stations have been stored in memory, "END" will appear for
about 4 seconds.
about 4 seconds.
z
If the RDS signals are very weak, station names may not be
stored in memory.
stored in memory.
To erase one of the contents of preset memory:
To erase all of the contents of preset memory:
z
After performing this operation, all of the preset memory informa-
tion will be erased.
tion will be erased.
To store a station name again if the wrong name was stored in
memory:
It may be impossible to store station names in memory using the
ASPM function if there is lots of noise or if the signal is too weak. In
this case, perform as follows.
memory:
It may be impossible to store station names in memory using the
ASPM function if there is lots of noise or if the signal is too weak. In
this case, perform as follows.
Notes:
z
The same station name can be stored in different channels.
z
In a certain area or during certain time periods, the station names
may temporarily be different.
may temporarily be different.
Notes for RDS operation
If any of the following events occur, it does not mean that the
unit is faulty:
unit is faulty:
z
"PS", "NO PS" and a station name appear alternately, and the
unit does not operate properly.
unit does not operate properly.
z
If a particular station is not broadcasting properly or a station is
conducting tests, the RDS reception function may not work prop-
erly.
conducting tests, the RDS reception function may not work prop-
erly.
z
When you receive an RDS station whose signal is too weak,
information like the station name may not be displayed.
information like the station name may not be displayed.
z
"NO PS" or "NO PTY" will flash for about 5 seconds, and then the
frequency will be displayed.
frequency will be displayed.
1
Press the PRESET ( or ) button to select the preset channel
number you want to erase.
number you want to erase.
2
Press the MEMORY button.
3
Within 5 seconds, press the CLEAR button.
1
Press the ON/STAND-BY button to enter the power stand-by
mode.
mode.
2
Whilst pressing down the MEMORY/SET button and move the
operation lever toward PRESET , press the ON/STAND-BY
button until "Preset Clear" appears.
operation lever toward PRESET , press the ON/STAND-BY
button until "Preset Clear" appears.
1 Press the PRESET ( or ) button to check whether the names
are correct.
2 If you find a wrong name during receiving the station, wait until the
correct name will be displayed. And then press the MEMORY but-
ton.
ton.
3 Within 5 seconds, press the MEMORY button whilst the preset
channel number is flashing.
z
The new station name has been stored in memory correctly.
Click on the first or last page to see other XL-DAB9H service manuals if exist.