Read Sharp XL-50 Service Manual online
XL-40H/50H
– 8 –
Figure 8-4
How to remove the pickup (See Fig. 8-4)
1. Remove the mechanism cover, paying attention to the
pawls (A1) x 4 pcs.
2. Remove the screws (A2) x 2 pcs., to remove the shaft (A3)
x 1 pc.
3. Remove the stop washer (A4) x 1 pc., to remove the gear
(A5) x 1 pc.
4. Remove the pickup.
Note:
After removing the optical pickup connector wrap the front
end of connector in conductive aluminium foil so as to
prevent damage of optical pickup by static electricity.
end of connector in conductive aluminium foil so as to
prevent damage of optical pickup by static electricity.
CD MECHANISM SECTION
Perform steps 1, 2 and 10, 11 of the disassembly method to
remove the CD mechanism.
remove the CD mechanism.
Pickup Unit
(A2) x2
ø2.6 x6mm
ø2.6 x6mm
(A1) x2
CD Mechanism
Shaft
(A3) x1
(A3) x1
Gear
(A5) x1
(A5) x1
StopWasher
(A4) x1
(A4) x1
Mechanism Cover
(A1) x2
How to remove the tape mechanism PWB
(See Fig. 8-2.)
(See Fig. 8-2.)
1. Remove the screws (F1) x 1 pc., to remove the tape
mechanism PWB.
2. Remove the screws (F2) x 1 pc.
3. Remove the solder joints (F3) x 2 pcs., to remove the tape
3. Remove the solder joints (F3) x 2 pcs., to remove the tape
mechanism PWB.
How to remove the jog motor
(See Figs. 8-3.)
(See Figs. 8-3.)
1. Remove the side panel and top cabinet.
2. Remove the jog belt (G1) x 1 pc., from the motor pulley.
3. Remove the screws (G2) x 2 pcs., to remove the jog motor.
Note:
When putting on the belt, ascertain that the belt is not twisted,
and clean it.
2. Remove the jog belt (G1) x 1 pc., from the motor pulley.
3. Remove the screws (G2) x 2 pcs., to remove the jog motor.
Note:
When putting on the belt, ascertain that the belt is not twisted,
and clean it.
Figure 8-2
Figure 8-3
(G2)x2
ø2x5mm
ø2x5mm
Worm
Gear
Gear
Jog Belt
(G1)x1
(G1)x1
Jog Motor
Holder
Holder
Jog Motor
Display PWB
Figure 8-1
How to remove the flywheel (See Fig. 8-1.)
1. Remove the belt.
2. Remove the stop washer (E1) x 1 pc., with a small precision
2. Remove the stop washer (E1) x 1 pc., with a small precision
screwdriver to extract the flywheel from the capstan metal.
Note:
When the stop washer is deformed or damaged, replace it
with a new one.
When the stop washer is deformed or damaged, replace it
with a new one.
How to reinstall the parts
Install each part in the reverse order of the removal with care.
Stop
Washer
Washer
Driver
(E1)x1
Stop Washer
Stop Washer
Mechanism
Chassis
Chassis
Washerx2
Flywheel
Tape
Mechanism
PWB
Mechanism
PWB
Tape
Mechanism
PWB
Mechanism
PWB
(F3)x2
Solder
Joint
Solder
Joint
(F2)x1
ø2x8mm
ø2x8mm
(F1)x1
ø2x3mm
ø2x3mm
Click on the first or last page to see other XL-50 service manuals if exist.