Read Sharp XL-30 (serv.man2) User Guide / Operation Manual online
9
SETTING THE CLOCK
1
Press the CLOCK/TIMER/SLEEP button to en-
ter the time check mode.
ter the time check mode.
2
Within 3 seconds, press the MEMORY/SET but-
ton.
ton.
3
Turn the jog dial to select the time display mode.
0:00 AM 12:00
“0:00”
→
The 24-hour display will appear.
(0:00 - 23:59)
(0:00 - 23:59)
“AM 12:00”
→
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
(AM 12:00 - PM 11:59)
●
Note that this can only be set when the unit is
first installed or it has been reset (see page 20).
first installed or it has been reset (see page 20).
4
Press the MEMORY/SET button.
5
Adjust the hour by turning the jog dial.
●
When the jog dial is turned one click clockwise,
the time will increase by 1 hour. When it is turned
one click anti-clockwise, the time will decrease
by 1 hour.
Keep turning the jog dial to change the time con-
tinuously.
the time will increase by 1 hour. When it is turned
one click anti-clockwise, the time will decrease
by 1 hour.
Keep turning the jog dial to change the time con-
tinuously.
●
When the 12-hour display is selected, “AM” will
change automatically to “PM”.
change automatically to “PM”.
(Main unit operation)
In this example, the clock is set for the 24-hour
(0:00) system.
In this example, the clock is set for the 24-hour
(0:00) system.
CLOCK/TIMER/
SLEEP
SLEEP
MEMORY/SET
Jog dial
6
Press the MEMORY/SET button.
7
Adjust the minutes by turning the jog dial.
●
When the jog dial is turned one click clockwise,
the time will increase by 1 minute. When it is
turned one click anti-clockwise, the time will de-
crease by 1 minute.
Keep turning the jog dial to change the time con-
tinuously.
the time will increase by 1 minute. When it is
turned one click anti-clockwise, the time will de-
crease by 1 minute.
Keep turning the jog dial to change the time con-
tinuously.
●
The hour setting will not advance even if min-
utes advance from “59” to “00”.
utes advance from “59” to “00”.
8
Press the MEMORY/SET button.
●
The clock starts operating from “0” second. (Sec-
onds are not displayed.)
onds are not displayed.)
Note:
●
In the event of a power failure or when the AC
power lead is disconnected, the clock display will
go out.
When the AC power supply is restored, the clock
display will flash on and off to indicate the time
when the power failure occurred or when the AC
power lead was disconnected.
If this happens, follow the procedure below to
change the clock time.
power lead is disconnected, the clock display will
go out.
When the AC power supply is restored, the clock
display will flash on and off to indicate the time
when the power failure occurred or when the AC
power lead was disconnected.
If this happens, follow the procedure below to
change the clock time.
To change the clock time:
Perform steps 1, 2 and 4 - 8 above.
Perform steps 1, 2 and 4 - 8 above.
To change the time display mode:
1
Perform steps 1 - 3 in the section “RESETTING
THE MICROCOMPUTER”, on page 20.
THE MICROCOMPUTER”, on page 20.
2
Perform steps 1 - 8 above.
*XL-30H(SUK)P09-P13
00.2.3, 2:00 PM
9
Click on the first or last page to see other XL-30 (serv.man2) service manuals if exist.