Read Sharp SD-EX200 User Guide / Operation Manual online
13
SD-EX200H_uk.fm
03/2/18
SD-EX200H
Prepara
tion f
o
r U
s
e
-
S
e
tti
ng the
c
loc
k
-
Setting the clock
By setting the unit to the correct time, you can use it not only as a clock but also for
timer playback.
timer playback.
In this example, the clock is set for the 24-hour (0:00) display.
[When the power is on]
Press the TIMER button.
Within 10 seconds, press the CURSOR ( or ) button to display the time.
The time display will appear for about 10 seconds.
Press the TIMER button.
Within 10 seconds, press the CURSOR ( or ) button to display the time.
The time display will appear for about 10 seconds.
Note:
The "CLOCK" will appear at the push of the DISPLAY button when the AC power
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from the beginning.
To change the 24-hour or 12-hour display:
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TIMER button.
3
Within 10 seconds, press the CURSOR ( or ) button to select
"CLOCK", and press the ENTER button.
"CLOCK", and press the ENTER button.
4
Press the CURSOR ( or ) but-
ton to select 24-hour or 12-
hour display and then press
the ENTER button.
ton to select 24-hour or 12-
hour display and then press
the ENTER button.
"0:00"
The 24-hour display will appear. (0:00 - 23:59)
"AM 12:00"
The 12-hour display will appear. (AM 12:00 - PM 11:59)
"AM 0:00"
The 12-hour display will appear. (AM 0:00 - PM 11:59)
Note that this can only be set when the unit is first installed or it has been reset.
[Refer to "Clearing all the memory (reset)" on page 29 for details.]
[Refer to "Clearing all the memory (reset)" on page 29 for details.]
5
Press the CURSOR ( or ) but-
ton to adjust the hour and then
press the ENTER button.
ton to adjust the hour and then
press the ENTER button.
"
Press the CURSOR ( or ) button once to advance the time by 1 hour. Hold
it down to advance continuously.
it down to advance continuously.
"
When the 12-hour display is selected, "AM" will change automatically to "PM".
6
Press the CURSOR ( or ) but-
ton to adjust the minutes and
then press the ENTER button.
ton to adjust the minutes and
then press the ENTER button.
"
Press the CURSOR ( or ) button once to advance the time by 1 minute.
Hold it down to advance by 5 minutes.
Hold it down to advance by 5 minutes.
"
The hour will not advance even if minutes advance from "59" to "00".
"
The clock begins counting from "0" seconds. (Seconds are not displayed.)
The time display will disappear after a few seconds.
The time display will disappear after a few seconds.
To confirm the time display:
[When the unit is in the stand-by mode]
Press the DISPLAY button on the remote control.
The time display will appear for about 5 seconds.
Press the DISPLAY button on the remote control.
The time display will appear for about 5 seconds.
1. Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on
page 29 for details.]
2. Perform "Setting the clock" from the beginning.
Click on the first or last page to see other SD-EX200 service manuals if exist.