Read Sharp CD-CH1500 (serv.man3) Service Manual online
CD-CH1500H/CD-CH1500W
– 8 –
OPERATION MANUAL
CP-RW5500H/CP-RW5500W
1. Woofer
2. Tweeter
3. Subwoofer
4. Subwoofer Terminals
5. Main Speaker Terminals
6. Bass Reflex Duct
2. Tweeter
3. Subwoofer
4. Subwoofer Terminals
5. Main Speaker Terminals
6. Bass Reflex Duct
1
2
3
4
5
6
Speaker System
Setting the Clock
In this example, the clock is set for the 24-hour (0:00) display.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the MENU button.
3
Turn the jog dial to select "CLOCK" and within 10 seconds, press
the ENTER button.
the ENTER button.
4
Turn the jog dial to select the 24-hour or 12-hour display and within
2 minutes, press the ENTER button.
2 minutes, press the ENTER button.
Note that this can only be set when the unit is first installed or it has been reset.
[Refer to "Clearing all the memory (reset)".]
[Refer to "Clearing all the memory (reset)".]
5
Turn the jog dial to adjust the hour and within 2 minutes, press the
ENTER button.
ENTER button.
When the 12-hour display is selected, "AM" will change automatically to "PM".
6
Turn the jog dial to adjust the minutes and within 2 minutes, press
the ENTER button.
the ENTER button.
The hour will not advance even if minutes advance from "59" to "00".
The clock starts from "0" second. (Seconds are not displayed.) The time display
will disappear after a few seconds.
The clock starts from "0" second. (Seconds are not displayed.) The time display
will disappear after a few seconds.
To confirm the time display:
Note:
"CLOCK" will appear or time will flash at the push of the DISPLAY button when the
AC power supply is restored after a power failure or unplugging the unit. Reset the
clock as follows.
"CLOCK" will appear or time will flash at the push of the DISPLAY button when the
AC power supply is restored after a power failure or unplugging the unit. Reset the
clock as follows.
To reset the clock:
To change the 24-hour or 12-hour display:
"0:00"
The 24-hour display will appear.
(0:00 - 23:59)
(0:00 - 23:59)
"AM 12:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
(AM 12:00 - PM 11:59)
"AM 0:00"
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
(AM 0:00 - PM 11:59)
[When the unit is in the stand-by mode]
Press the DISPLAY button on the remote control. The
time display will appear for about 3 seconds.
time display will appear for about 3 seconds.
[When the power is on]
Press the MENU button. The time display will appear
for about 10 seconds.
for about 10 seconds.
[When time is flashing]
1
Press the ON/STAND-BY button.
2
Press the MENU button.
3
Press the ENTER button.
4
Perform "Setting the Clock" from step 5.
[When "CLOCK" appears]
Perform "Setting the Clock" from the beginning.
1 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)".]
2 Perform "Setting the Clock" from the beginning.
2 Perform "Setting the Clock" from the beginning.
Click on the first or last page to see other CD-CH1500 (serv.man3) service manuals if exist.