Read Sharp CD-C661H (serv.man2) Service Manual online
CD-C661H/HR
– 6 –
OPERATION MANUAL
SETTING THE CLOCK
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Press
the
TUNING/TIME
(
or
) button to select the time
display mode.
"0:00"
→
T
h
e
24
-h
o
u
r d
isp
la
y w
ill
ap
pe
ar
.
(
0
:0
0
-
2
3
:5
9
)
"AM 0:00"
→
The 12-hour display will appear.
(
A
M
0
:0
0
-
P
M
1
1
:5
9
)
"AM 12:00"
→
The 12-hour display will appear.
(
A
M
1
2
:0
0
-
P
M
1
1
:5
9
)
Note that this can only be set when the unit is first installed
or it has been reset.
5
Press the MEMORY/SET button.
6
Press
the
TUNING/TIME
(
or
) button to adjust the hour.
Press
the
TUNING/TIME
(
or
) button once to advance
the time by 1 hour. Hold it down to advance continuously.
When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
7
Press the MEMORY/SET button.
8
P
re
s
s
th
e
TU
N
IN
G
/TI
M
E
(
o
r
) b
u
tt
o
n
to
a
d
ju
s
t
th
e
minutes.
Press
the
TUNING/TIME
(
or
) button once to advance
the time by 1 minute. Hold it down to change the time in 5
minute intervals.
The hour setting will not advance even if minutes advance from
"59" to "00".
9
Press the MEMORY/SET button.
The clock starts operating from "0" seconds.
(Seconds are not displayed.)
To see the time display:
CLOCK
ON/
STAND-BY
MEMORY/
SET
TUNING/
TIME
( )
AM 12:00
AM 0:00
0:00
2
3
4
7
6
5
8
9
Press the CLOCK button.
The time display will appear for about 5 seconds.
Note:
The clock display will flash on and off at the push of the CLOCK
button when the AC power supply is restored after a power
failure occurs or after the AC power lead is disconnected.
If this happens, follow the procedure below to change the clock
time.
To change the clock time:
Press the CLOCK button.
Within 5 seconds, press the MEMORY/SET button.
Perform steps 6 - 9 above.
To change the time display mode:
Perform steps 1 - 2 in the section "RESETTING THE MICRO-
COMPUTER", on page 28.
Perform steps 1 - 9 above.
(Main unit operation)
In this example, the clock is set for the
24-hour (0:00) system.
1
2
1
3
2
PREPARATION FOR USE
15
15
Remote control
Notes concerning use:
Replace the batteries if the operating distance is reduced or if
the operation becomes erratic.
Periodically clean the transmitter LED on the remote control
and the sensor on the main unit with a soft cloth.
Exposing the sensor on the main unit to strong light may in-
terfere with operation. Change the lighting or the direction of
the unit.
Keep the remote control away from moisture, excessive heat,
shock, and vibrations.
0.2 m - 6 m
(8" - 20')
2
1,2
RESETTING THE MICROCOMPUTER
Reset the microcomputer under the following conditions:
To erase all of the stored memory contents (clock and timer
settings, and tuner and CD presets).
If the display is not correct.
If the operation is not correct.
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Whilst pressing down the
button and the
button, hold down the ON/STAND-BY button for at least 1
second.
Caution:
The operation explained above will erase all data stored in
memory including clock and timer settings, and tuner and CD
presets.
Click on the first or last page to see other CD-C661H (serv.man2) service manuals if exist.