Read Sharp CD-BA2010 (serv.man9) Service Manual online
CD-BA2010H
– 6 –
OPERATION MANUAL
SETTING THE CLOCK
In this example, the clock is set for the 24-hour (0:00) system.
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Press theTUNING/TIME ( or ) button to select the time
display mode.
“0:00”
→
The 24-hour display will appear.
(0:00 - 23:59)
“AM 0:00”
→
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
“AM 12:00”
→
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
Note that this can only be set when the unit is first in-
stalled or it has been reset.
5
Press the MEMORY/SET button.
6
Press the TUNING/TIME ( or ) button to adjust the hour.
Press the TUNING/TIME ( or ) button once to ad-
vance
the time by 1 hour
. Hold it down to advance con-
tinuously
.
When the 12-hour display is selected, “AM” will change
automatically to
“PM”.
7
Press the MEMOR
Y/SET
button.
8
Press the
TUNING/TIME (
or
) button to adjust the min-
utes.
Press the
TUNING/TIME (
or
) button once to ad-
vance
the time by 1 minute. Hold it down to change the
time in 5
minute intervals.
The hour setting will not advance even if minutes advance
from “59” to “00”.
9
Press the MEMOR
Y/SET
button.
The clock starts operating from “0” second.
(Seconds are not displayed.)
And then the clock display will disappear after a few sec-
onds.
T
o
see the time display:
Press the CLOCK button.
The time display will appear for about 5 seconds.
Note:
The clock display will flash on and of
f at the push of the
CLOCK button when the
AC power supply is restored after
a power failure occurs or after the
AC power lead is discon-
nected.
If this happens, follow the procedure below to change the
clock time.
T
o
change the clock time:
1
Press the CLOCK button.
2
Within 5 seconds, press the MEMOR
Y/SET
button.
3
Perform steps 6 - 9 above.
T
o
change the time display mode:
1
Perform steps 1 - 2 in the section “RESETTING
THE
MICROCOMPUTER”.
2
Perform steps 1 - 9 above.
(Main unit operation)
REMOTE CONTROL
0.2 m - 6 m
(8" - 20’)
Notes concerning use:
Replace the batteries if the operating distance is reduced or
if the operation becomes erratic.
Periodically clean the transmitter LED on the remote con-
trol and the sensor on the main unit with a soft cloth.
Exposing the sensor on the main unit to strong light may
interfere with operation. Change the lighting or the direction
of the unit.
Keep the remote control away from moisture, excessive heat,
shock, and vibrations.
RESETTING THE MICROCOMPUTER
Reset the microcomputer under the following con-
ditions:
T
o
erase all of the stored memory contents (clock and timer
settings, and tuner and CD presets).
If the display is not correct.
If the operation is not correct.
1
Press the ON/ST
AND-BY
button to enter the stand-by mode.
2
Whilst pressing down the
/
button and the X-BASS/
DEMO
button, hold down the ON/ST
AND-BY
button for at
least 1 second.
“CLEAR
AL” will appear
.
Caution:
The operation explained above will erase all data stored in
memory including clock and timer settings, and tuner and
CD presets.
Click on the first or last page to see other CD-BA2010 (serv.man9) service manuals if exist.