Read Panasonic TX-47PT10F / TX-47PT10P Service Manual online
ADJUSTMENT PROCEDURE
Item / Preparation
Adjustment/Confirmation
+B SET-UP
4. Receive a Window pattern.
5. Set the controls :-
5. Set the controls :-
Brightness
Minimum
Contrast
Minimum
Volume
Minimum
Confirm the following voltages.
A - Board
A1 Pin2
A1 Pin2
7.5
± 0.5V
IC1252 Pin2
2.5
±
0.25V
A1 Pin12
-20
±
0.5V
IC1251 Pin3
3.3
+0.3 / -0.2V
A1 Pin16
20
±
0.5V
IC7101 Pin3
5
±
0.4V
A2 Pin15
30
±
0.5V
IC2708 Pin4
9
±
0.4V
A2 Pin6
15
±
0.5V
C2703 + side
8
±
0.4V
A3 Pin4
15
±
0.5V
IC2706 Pin2
5
±
0.2V
A3 Pin2
-15
±
0.5V
IC2705 Pin2
3.3
±
0.2V
IC2709 Pin2
3.3
±
0.2V
D – Board
D5 Pin1
D5 Pin1
210
±
3V
D5 Pin8
140
±
2V
D3 Pin3
18
±
2V
D3 Pin1 -18
±
2V
D2 Pin5
15
±
1.5V
D5 Pin6
6.4
±
0.24V
D1 Pin8
12
±
0.5V
D2 Pin13
40
±
3V
with SW1 Open
D2 Pin13
30
±
2V
with SW1 Closed
CUT OFF
1. Picture menu:Normal.
2. Normalised conditions.
3. Colour balance normal.
4. AI:OFF
2. Normalised conditions.
3. Colour balance normal.
4. AI:OFF
P-NR:OFF.
5. Screen VR: fully anticlockwise.
6. B-G-ST1:120 Sub-Bright:50.
7. High R:70 High G:128 High B:70.
8. Low R:128 Low G:150 Low B:80
6. B-G-ST1:120 Sub-Bright:50.
7. High R:70 High G:128 High B:70.
8. Low R:128 Low G:150 Low B:80
To adjust Cutoff select AV1 with no signal. Ensure that the PTV is normalised.
Adjust R-Screen VR so that the voltage , IK at test point TPLR1 is 165 ± 2V.
G-Screen VR so that the voltage , IK at test point TPLG1 is 160 ± 2V.
B-Screen VR so that the voltage , IK at test point TPLB1 is 165 ± 2V.
Adjust R-Screen VR so that the voltage , IK at test point TPLR1 is 165 ± 2V.
G-Screen VR so that the voltage , IK at test point TPLG1 is 160 ± 2V.
B-Screen VR so that the voltage , IK at test point TPLB1 is 165 ± 2V.
SELF CHECK
Self – check is used to automatically check the bus lines and hexadecimal code of the TV set.To enter Self-Check mode
press the down (-/v) button on the customer controls at the front of the TV set , at the same time pressing the STATUS
button on the remote control. To exit Self-Check , switch off the tv set at the power button.
If the CCU ports have been checked and found to be incorrect or not located , then “ - - “ will appear in place of “ O.K. “.
NOTE: Self Check should only be used when refurbishing the TV set and not during normal repair work.
press the down (-/v) button on the customer controls at the front of the TV set , at the same time pressing the STATUS
button on the remote control. To exit Self-Check , switch off the tv set at the power button.
If the CCU ports have been checked and found to be incorrect or not located , then “ - - “ will appear in place of “ O.K. “.
NOTE: Self Check should only be used when refurbishing the TV set and not during normal repair work.
To exit Self-Check, switch off the TV set at the power button.
5
If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.".
Factory use only
Sum:****
MEM
:
O.K.
GC1
:
O.K.
VDU
:
O.K.
CIP
:
O.K.
RGB
:
O.K.
AVSW
:
O.K.
TUN1
:
O.K.
DAC1
:
O.K.
MSP
:
O.K
CONV
:
O.K.
CVDAC
:
O.K.
WBDAC
:
O.K.
OPTION 1 :
OPTION 2 :
OPTION 3 :
OPTION 4 :
OPTION 5 :
OPTION 6 :
OPTION 7 :
OPTION 8 :
OPTION 9 :
OPTION 10:
OPTION 11:
OPTION 12:
OPTION 13:
Check :
OPTION 2 :
OPTION 3 :
OPTION 4 :
OPTION 5 :
OPTION 6 :
OPTION 7 :
OPTION 8 :
OPTION 9 :
OPTION 10:
OPTION 11:
OPTION 12:
OPTION 13:
Check :
TX-47PT10F
0F
00
00
B0
11
00
50
F7
00
50
F7
D0
00
80
09
80
09
C0
FA
2A
FA
2A
TX-47PT10F/P
0F
00
00
B0
11
00
50
F7
00
50
F7
D0
00
80
09
80
09
C0
FA
2A
FA
2A
Click on the first or last page to see other TX-47PT10F / TX-47PT10P service manuals if exist.