Read Panasonic TX-42PT10 Service Manual online
ADJUSTMENT PROCEDURE
Item / Preparation
Adjustment/Confirmation
+B SET-UP
4. Receive a Window pattern.
5. Set the controls :-
5. Set the controls :-
Brightness
Minimum
Contrast
Minimum
Volume
Minimum
Confirm the following voltages.
A - Board
A1 Pin2
A1 Pin2
7.5
± 0.5V
IC1252 Pin2
2.5
±
0.25V
A1 Pin12
-20
±
0.5V
IC1251 Pin3
3.3
+0.3 / -0.2V
A1 Pin16
20
±
0.5V
IC7101 Pin3
5
±
0.4V
A2 Pin15
30
±
0.5V
IC2708 Pin4
9
±
0.4V
A2 Pin6
15
±
0.5V
C2703 + side
8
±
0.4V
A3 Pin4
15
±
0.5V
IC2706 Pin2
5
±
0.2V
A3 Pin2
-15
±
0.5V
IC2705 Pin2
3.3
±
0.2V
IC2709 Pin2
3.3
±
0.2V
D – Board
D5 Pin1
D5 Pin1
210
±
3V
D5 Pin8
140
±
2V
D3 Pin3
18
±
2V
D3 Pin1 -18
±
2V
D2 Pin5
15
±
1.5V
D5 Pin6
6.4
±
0.24V
D1 Pin8
12
±
0.5V
D2 Pin13
40
±
3V
with SW1 Open
D2 Pin13
30
±
2V
with SW1 Closed
CUT OFF
1. Picture menu:Normal.
2. Normalised conditions.
3. Colour balance normal.
4. AI:OFF
2. Normalised conditions.
3. Colour balance normal.
4. AI:OFF
P-NR:OFF.
5. Screen VR: fully anticlockwise.
6. B-G-ST1:120 Sub-Bright:50.
7. High R:70 High G:128 High B:70.
8. Low R:128 Low G:150 Low B:80
6. B-G-ST1:120 Sub-Bright:50.
7. High R:70 High G:128 High B:70.
8. Low R:128 Low G:150 Low B:80
To adjust Cutoff select AV1 with no signal. Ensure that the PTV is normalised.
Adjust R-Screen VR so that the voltage , IK at test point TPLR1 is 165 ± 2V.
G-Screen VR so that the voltage , IK at test point TPLG1 is 160 ± 2V.
B-Screen VR so that the voltage , IK at test point TPLB1 is 165 ± 2V.
Adjust R-Screen VR so that the voltage , IK at test point TPLR1 is 165 ± 2V.
G-Screen VR so that the voltage , IK at test point TPLG1 is 160 ± 2V.
B-Screen VR so that the voltage , IK at test point TPLB1 is 165 ± 2V.
SELF CHECK
To return customer settings to factory settings and clear owner ID of all information input by the customer , enter Self –Check
Mode.To get into Self-Check mode press the down (-/v) button on the customer controls at the front of the TV set, at the
same time pressing the STATUS button on the remote control. To exit Self-Check , switch off the tv set at the power
button.
NOTE: Self Check should only be used when refurbishing the TV set and not during normal repair work.
Mode.To get into Self-Check mode press the down (-/v) button on the customer controls at the front of the TV set, at the
same time pressing the STATUS button on the remote control. To exit Self-Check , switch off the tv set at the power
button.
NOTE: Self Check should only be used when refurbishing the TV set and not during normal repair work.
To exit Self-Check, switch off the TV set at the power button.
5
If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.".
Factory use only
Sum
:
****
MEM
:
O.K.
GC1
:
O.K.
VDU
:
O.K.
CIP
:
O.K.
RGB
:
O.K.
AVSW
:
O.K.
TUN1
:
O.K.
DAC1
:
O.K.
MSP
:
O.K.
CONV
:
O.K.
CVDAC
:
O.K.
WBDAC
:
O.K.
OPTION 1 :
OPTION 2 :
OPTION 3 :
OPTION 4 :
OPTION 5 :
OPTION 6 :
OPTION 7 :
OPTION 8 :
OPTION 9 :
OPTION 10:
OPTION 11:
OPTION 12:
OPTION 13:
Check :
OPTION 2 :
OPTION 3 :
OPTION 4 :
OPTION 5 :
OPTION 6 :
OPTION 7 :
OPTION 8 :
OPTION 9 :
OPTION 10:
OPTION 11:
OPTION 12:
OPTION 13:
Check :
TX-42PT10
01
00
10
10
00
50
84
40
00
80
19
88
00
10
10
00
50
84
40
00
80
19
88
FA
50
Click on the first or last page to see other TX-42PT10 service manuals if exist.