Read Panasonic KX-TG7205RUJ / KX-TG7205RUM / KX-TG7205RUS / KX-TG7205RUT / KX-TG7206RUM / KX-TG7206RUS / KX-TG7206RUT / KX-TGA720RUJ / KX-TGA720RUM / KX-TGA720RUS / KX-TGA720RUT Service Manual online
40
KX-TG7205RU/KX-TG7206RU/KX-TGA720RU
(H) DTMF Generator Check
-
1. Connect CN1 (Telephone Socket) to DTMF tester. (Road=600
Ω)
2. Link Handset and push dial key.
3. Confirm DTMF character.
4. Confirm that the high Group is -3 ± 2 dBm.
5. Confirm that the low Group is -6 ± 2 dBm.
3. Confirm DTMF character.
4. Confirm that the high Group is -3 ± 2 dBm.
5. Confirm that the low Group is -6 ± 2 dBm.
IC7, R116,
C141, R29, C22,
C23, R18~R24,
C14~C17, Q5,
D4
(I)* Transmitted Power Con-
firmation
-
Remove the Antenna before starting step from 1 to 7.
1. Configure the DECT tester (CMD60) as follows;
<Setting>
• Short A_1 and GND.
• Test mode: FP
• Traffic Carrier: 5
• Traffic Slot: 4
• Mode: Loopback
• PMID: 00000
• RF LEVEL = -70 dBm.
• Test mode: FP
• Traffic Carrier: 5
• Traffic Slot: 4
• Mode: Loopback
• PMID: 00000
• RF LEVEL = -70 dBm.
2. Execute the command “testmode”.
3. Execute the command “sendchar dmv 2 2”.
4. Check that “Signalling Status” has been set to “Locked”, then press “ACCEPT
3. Execute the command “sendchar dmv 2 2”.
4. Check that “Signalling Status” has been set to “Locked”, then press “ACCEPT
RFPI”.
5. Initiate connection from Dect tester (“set up connect”)
6. Execute the command “ANT1”.
7. Confirm that the NTP value at ANT is 20.7 dBm ~ 25.7 dBm.
6. Execute the command “ANT1”.
7. Confirm that the NTP value at ANT is 20.7 dBm ~ 25.7 dBm.
IC7, IC10, L7,
C117, C118,
C124, C125,
R106, R109,
R106, R109,
DA1, C112,
R111, C126,
C127, R112,
R125, C128
(J)* Modulation Check and
Adjustment
-
Follow steps 1 to 6 of (I).
7.Confirm that the B-Field Modulation is +220 ~ +403/-220 ~ -403 kHz/div &
Modulated width 670 kHz using data type Fig31.
8.Adjust the B-Field Modulation if required. (Execute the command “readmod”
and “wrtmod xx”, where xx is the value.)
Modulated width 670 kHz using data type Fig31.
8.Adjust the B-Field Modulation if required. (Execute the command “readmod”
and “wrtmod xx”, where xx is the value.)
IC7, IC10, L7,
C117, C118,
C124, C125,
R106, R109,
R106, R109,
DA1, C112,
R111, C126,
C127, R112,
R125, C128
(K)* Frequency Offset Check
-
Follow steps 1 to 6 of (I).
7.Confirm that the frequency offset is < ± 50 kHz.
IC7, IC10, L7,
C117, C118,
C124, C125,
R106, R109,
R106, R109,
DA1, C112,
R111, C126,
C127, R112,
R125, C128
(L)* Frequency Drift Confir-
mation
-
Follow steps 1 to 6 of (I).
7.Confirm that the frequency drift is < ± 30 kHz/ms.
IC7, IC10, L7,
C117, C118,
C124, C125,
R106, R109,
R106, R109,
DA1, C112,
R111, C126,
C127, R112,
R125, C128
(M)*
Sensitivity Receiver
Confirmation
-
Follow steps 1 to 6 of (I).
7.Set DECT tester power to -90 dBm.
8.Confirm that the BER is < 1000 ppm.
8.Confirm that the BER is < 1000 ppm.
IC7, IC10, L7,
C117, C118,
C124, C125,
R106, R109,
R106, R109,
DA1, C112,
R111, C126,
C127, R112,
R125, C128
(N)*
Timing Confirmation
-
Follow steps 1 to 6 of (I).
7.Confirm that the Timing accuracy is < ± 5.0 ppm.
IC7, IC10, L7,
C117, C118,
C124, C125,
R106, R109,
R106, R109,
DA1, C112,
R111, C126,
C127, R112,
R125, C128
(O)* Power RAMP Confirma-
tion
-
Follow steps 1 to 6 of (I).
7.Confirm that Power RAMP is matching.
IC7, IC10, L7,
C117, C118,
C124, C125,
R106, R109,
R106, R109,
DA1, C112,
R111, C126,
C127, R112,
R125, C128
Items
Check
Point
Procedure
Check or
Replace Parts
Click on the first or last page to see other KX-TG7205RUJ / KX-TG7205RUM / KX-TG7205RUS / KX-TG7205RUT / KX-TG7206RUM / KX-TG7206RUS / KX-TG7206RUT / KX-TGA720RUJ / KX-TGA720RUM / KX-TGA720RUS / KX-TGA720RUT service manuals if exist.