Read Panasonic KX-TG7125RUS / KX-TG7125RUT / KX-TGA711RUS / KX-TGA711RUT Service Manual online
65
KX-TG7125RUS/KX-TG7125RUT/KX-TGA711RUS/KX-TGA711RUT
11.6. Things to Do after Replacing IC
Cautions:
Since this page is common to each country, it may not apply to some models in your country. The contents below are the mini-
mum adjustments required for operation.
mum adjustments required for operation.
11.6.1. Base Unit
Before doing the following adjustment, be sure to do PC Setting (P.58) in The Setting Method of JIG (Base Unit).
Note:
(*1) XX: country code, YY: revision number, ZZ: Voice Prompt
“XX”, “YY” and “ZZ” vary depending on the country version. You can find them in the batch file, PQZZ- mentioned in JIG and PC
(P.58).
(*2) Refer to Check Point (Base Unit) (P.43)
“XX”, “YY” and “ZZ” vary depending on the country version. You can find them in the batch file, PQZZ- mentioned in JIG and PC
(P.58).
(*2) Refer to Check Point (Base Unit) (P.43)
11.6.2. Handset
Before doing the following adjustment, be sure to do PC Setting (P.59) in The Setting Method of JIG (Handset).
Note:
(*3) XX: country code, YY: revision number
“XX” and “YY” vary depending on the country version. You can find them in the batch file, PQZZ- mentioned in JIG and PC
(P.58).
“XX” and “YY” vary depending on the country version. You can find them in the batch file, PQZZ- mentioned in JIG and PC
(P.58).
(*4) Refer to Check Point (Handset) (P.47)
IC
Necessary Adjustment
BBIC
(IC7)
(IC7)
Programs for Voice processing, interface for RF and
EEPROM
EEPROM
1. Default batch file: Execute the command “default.bat”.
2. Country version batch file: Execute the command
2. Country version batch file: Execute the command
“TG7120XXrevYY.bat”. (*1)
3. Clock adjustment: Refer to Check Point (F). (*2)
EEPROM
(IC5)
(IC5)
Adjustment parameter data
(country version batch file, default batch file, etc.)
(country version batch file, default batch file, etc.)
1. Change the address “0000” of EEPROM to “55”.
2. Default batch file: Execute the command “default.bat”.
3. Country version batch file: Execute the command
2. Default batch file: Execute the command “default.bat”.
3. Country version batch file: Execute the command
“TG7120XXrevYY.bat”. (*1)
4. Clock adjustment: Refer to Check Point (F). (*2)
FLASH
(IC9)
(IC9)
Voice prompt data
(vary depending on country version)
(vary depending on country version)
1. Wait more than 15 seconds after connecting the JIG
Cables.
2. Execute the command “VPDL06 -8M ZZ.bin” (*1)
(writing time: aprox. 1.5 min.)
IC
Necessary Adjustment
BBIC
(IC1)
(IC1)
Programs for Voice processing, interface for RF and
EEPROM
EEPROM
1. Default batch file: Execute the command “default.bat”.
2. Default batch file (remaining): Execute the Command
2. Default batch file (remaining): Execute the Command
“TGA711DEFrevYY.bat”. (*3)
3. Country version batch file: Execute the command
“TGA711XXrevYY”. (*3)
4. Clock adjustment: Refer to Check Point (J). (*4)
5. 1.8 V setting and battery low detection: Refer to Check
5. 1.8 V setting and battery low detection: Refer to Check
Point (A), (H) and (I). (*4)
EEPROM
(IC3)
(IC3)
Adjustment parameter data
(country version batch file, default batch file, etc.)
(country version batch file, default batch file, etc.)
1. Change the address “0015” of EEPROM to “00”.
2. Default batch file: Execute the command “default.bat”.
3. Default batch file (remaining): Execute the Command
2. Default batch file: Execute the command “default.bat”.
3. Default batch file (remaining): Execute the Command
“TGA711DEFrevYY.bat”. (*3)
4. Country version batch file: Execute the command
“TGA711XXrevYY”. (*3)
5. Clock adjustment: Refer to Check Point (J). (*4)
6. 1.8 V setting and battery low detection: Refer to Check
6. 1.8 V setting and battery low detection: Refer to Check
Point (A), (H) and (I). (*4)
Click on the first or last page to see other KX-TG7125RUS / KX-TG7125RUT / KX-TGA711RUS / KX-TGA711RUT service manuals if exist.