Read Panasonic KX-TG6811UAB / KX-TG6811UAM / KX-TG6812UAB / KX-TG6821UAB / KX-TGA681RUB / KX-TGA681RUM Service Manual online
40
KX-TG6811UAB/KX-TG6811UAM/KX-TG6812UAB/KX-TG6821UAB/KX-TGA681RUB/KX-TGA681RUM
(H)*
Transmitted Power
Confirmation
ANT1
Short ANT1/2 pattern to GND.
1. Configure the DECT tester (CMD60) as follows;
<Setting>
• Test mode: FP
• Traffic Carrier: 5
• Traffic Slot: 4
• Mode: Loopback
• PMID: 00000
• RF LEVEL = -70 dBm.
• Traffic Carrier: 5
• Traffic Slot: 4
• Mode: Loopback
• PMID: 00000
• RF LEVEL = -70 dBm.
2. Execute the command ”sendchar TST”.
3. Execute the command “sendchar dmv 2 2”.
4. Check that “Signalling Status” has been set to “Locked”, then press “ACCEPT
3. Execute the command “sendchar dmv 2 2”.
4. Check that “Signalling Status” has been set to “Locked”, then press “ACCEPT
RFPI”.
5. Initiate connection from Dect tester (“set up connect”)
6. Execute the command “ANT1”.
7. Confirm that the NTP value at ANT is 18.5 dBm ~ 25.0 dBm.
6. Execute the command “ANT1”.
7. Confirm that the NTP value at ANT is 18.5 dBm ~ 25.0 dBm.
IC501, C819,
C893, C894,
C895, C896,
C895, C896,
DA802, L503,
L504
(I)*
Modulation Check
ANT1
Follow steps 1 to 6 of (H).
7.Confirm that the B-Field Modulation is -350 ± 50/+350 ± 50 kHz/div using data
type Fig31.
type Fig31.
Refer to (H)
(J)* Frequency Offset Check
ANT1
Follow steps 1 to 6 of (H).
7.Confirm that the frequency offset is < ±20 kHz.
Refer to (H)
(K)*
Sensitivity Receiver
Confirmation
ANT1
Follow steps 1 to 6 of (H).
7.Set DECT tester power to -88 dBm.
8.Confirm that the BER is < 1000 ppm.
8.Confirm that the BER is < 1000 ppm.
Refer to (H)
(L)*
Power RAMP
Confirmation
-
Follow steps 1 to 6 of (H).
7.Confirm that Power RAMP is matching.
Refer to (H)
(M)
Audio Check
-
1. Link with Handset which is connected to Line Simulator.
2. Set line voltage to 48 V and line current to 50 mA.
3. Input -45 dBm (600
2. Set line voltage to 48 V and line current to 50 mA.
3. Input -45 dBm (600
Ω)/1 kHz to MIC of Handset. Measure the Level at Line I/F
and distortion level.
4. Confirm that the level is -3 dBm ± 5 dB and that the distortion level is < 5 % at
TEL Line (600
Ω Load).
5. Input -20 dBm (600
Ω)/1 kHz to Line I/F. Measure the Level at Receiver of
Handset and distortion level (Receive volume set to second position from
minimum).
minimum).
6. Confirm that the level is -22 dBm ± 4 dB and that the distortion level is < 5 %
at Receiver (34
Ω Load).
IC501, SA101,
P101, D101,
Q141, Q142,
Q161, Q171,
Q161, Q171,
R141, R142,
R144, R145,
R144, R145,
D141, L505,
C184, R164,
R177, C173,
R171, R172,
R175, R176,
R177, C173,
R171, R172,
R175, R176,
R178
(N)
Charging Check
-
1. Connect Charge Contact 12
Ω/2 W resistor between charge+ and charge-.
2. Measure and confirm voltage across the resistor is 3.9 V ± 0.4 V.
R371, R372,
D362, C361
(O)
TAM Operation
Confirmation
(KX-6821 only)
-
1. TAM Confirmation (Execute the command "sendchar VPI").
2. Confirm the returned Value (Value is "DD87RN 00").
2. Confirm the returned Value (Value is "DD87RN 00").
IC501, IC601,
C601
Items
Check
Point
Procedure
Check or
Replace Parts
Click on the first or last page to see other KX-TG6811UAB / KX-TG6811UAM / KX-TG6812UAB / KX-TG6821UAB / KX-TGA681RUB / KX-TGA681RUM service manuals if exist.