Read Panasonic KX-TG6551RUM / KX-TGA650RUM / KX-TGA651RUM (serv.man3) Service Manual Supplement online
2
KX-TG6551RUM/KX-TGA650RUM/KXTGA651RUM
1 DELETION
1.1.
Base Unit
[Changed from original section “11.7.1.1.Base Unit”]
60
KX-TG6551RUM/KX-TGA650RUM/KX-TGA651RUM
11.7. Things to Do after Replacing IC or X'tal
If repairing or replacing EEPROM and X'tal, it is necessary to download the required data such as Programming data or adjustment
data, etc in memory.
The set doesn't operate if it is not executed.
data, etc in memory.
The set doesn't operate if it is not executed.
11.7.1. How to download the data
11.7.1.1. Base Unit
First, operate the PC setting according to The Setting Method of JIG (Base Unit) (P.53).
Then download the appropriate data according to the following procedures.
Then download the appropriate data according to the following procedures.
Note:
(*1) XX: country code, YY: revision number
“XX”, “YY” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting Method
of JIG (Base Unit) (P.53).
“XX”, “YY” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting Method
of JIG (Base Unit) (P.53).
Items
How to download/Required adjustment
BBIC (IC501)
Programming data is stored in memory.
1) Make sure to connect the JIG cable, then disconnect the DC
Power in order to download the data.
2) Execute the command “flw480 *********.hex”.
3) Connect the DC Power.
4) Press the PC Enter key once.
5) After a few minutes, “Successful upgrade” is displayed on the
PC indicating downloading has finished.
6) Detach the JIG cable, then disconnect the DC Power.
7) Connect the DC Power.
8) Connect the JIG cable again, and execute the command
“getchk”, then confirm the checksum value is correct.
. If the downloading fails, start again from step 1).
9) Default batch file: Execute the command “default.bat”.
10) Country version batch file: Execute the command
“TG6551EUXXrevYY.bat”. (*1)
11) Clock adjustment: Refer to Check Point (G). (*2)
Power in order to download the data.
2) Execute the command “flw480 *********.hex”.
3) Connect the DC Power.
4) Press the PC Enter key once.
5) After a few minutes, “Successful upgrade” is displayed on the
PC indicating downloading has finished.
6) Detach the JIG cable, then disconnect the DC Power.
7) Connect the DC Power.
8) Connect the JIG cable again, and execute the command
“getchk”, then confirm the checksum value is correct.
. If the downloading fails, start again from step 1).
9) Default batch file: Execute the command “default.bat”.
10) Country version batch file: Execute the command
“TG6551EUXXrevYY.bat”. (*1)
11) Clock adjustment: Refer to Check Point (G). (*2)
EEPROM (IC611)
Adjusted parameter data is stored in memory.
(country version batch file, default batch file,
etc.)
(country version batch file, default batch file,
etc.)
1) Change the address “0001” of EEPROM to “55” to download
the data.
2) Default batch file: Execute the command “default.bat”.
3) Country version batch file: Execute the command
“TG6551EUXXrevYY.bat”. (*1)
4) Clock adjustment
the data.
2) Default batch file: Execute the command “default.bat”.
3) Country version batch file: Execute the command
“TG6551EUXXrevYY.bat”. (*1)
4) Clock adjustment
X'tal (X1)
System clock
Clock adjustment data is in EEPROM, adjust the data again
after replacing it.
1) Apply 6.5V between DCP ad DCM with DC power.
2) Input Command "sendchar sfr", then you can confirm the
current value.
3) Check X'tal Frequency.(13.824 MHz ± 100 Hz).
4) If the frequency is not 13.824 MHz ± 100 Hz, adjust the
frequency of CLK executing the command "sendchar sfr xx xx
(where xx is the value)" so that the reading of the frequency
counter is 13.824000 MHz ± 15 Hz.
after replacing it.
1) Apply 6.5V between DCP ad DCM with DC power.
2) Input Command "sendchar sfr", then you can confirm the
current value.
3) Check X'tal Frequency.(13.824 MHz ± 100 Hz).
4) If the frequency is not 13.824 MHz ± 100 Hz, adjust the
frequency of CLK executing the command "sendchar sfr xx xx
(where xx is the value)" so that the reading of the frequency
counter is 13.824000 MHz ± 15 Hz.
D
eletion
Click on the first or last page to see other KX-TG6551RUM / KX-TGA650RUM / KX-TGA651RUM (serv.man3) service manuals if exist.