Read Panasonic WR-X22NL / WR-X22NH Service Manual online
– 2 –
●
Stereo Inputs 1 - 4
!1
Level Switches [INPUT +10/0/–10]
Is selected in accordance with an input signal level.
Adjust the sensitivity so that optimal volume is gained
when the input fader !5 stands at 8.
Adjust the sensitivity so that optimal volume is gained
when the input fader !5 stands at 8.
!2
Assign Switches [MAIN 1, MAIN 2, SUB 1, SUB 2]
Selects a bus line from among 4 channels for signal
transmission. Press one of the switches to select a bus
line and the integral green light comes on. Press the
switch again to stop transmission and the light comes
off. A combination of these switches' setup is called
"pattern", and up to 8 patterns can be registered.
transmission. Press one of the switches to select a bus
line and the integral green light comes on. Press the
switch again to stop transmission and the light comes
off. A combination of these switches' setup is called
"pattern", and up to 8 patterns can be registered.
!3
Signal Peak Indicators [SGNL/PEAK]
Lights in accordance with an input signal level. This
indicator becomes green when a signal is approx. 30
dB below the clip level and changes to red when a sig-
nal is approx. 8 dB below the clip level. These indica-
tors are useful for easy check of signal levels and level
change (setup by use of the level switch !1).
indicator becomes green when a signal is approx. 30
dB below the clip level and changes to red when a sig-
nal is approx. 8 dB below the clip level. These indica-
tors are useful for easy check of signal levels and level
change (setup by use of the level switch !1).
!4
Name Plates
Indicates the device name that is connected to an input
terminal.
terminal.
!5
Input Faders
Adjusts the sending level of an input signal.
The level is rated when the input fader stands at 8.
The level is rated when the input fader stands at 8.
y
Signal Peak Indicators [SGNL/PEAK]
Lights in accordance with an input signal level. This
indicator becomes green when a signal is approx. 30
dB below the clip level and changes to red when a sig-
nal is approx. 8 dB below the clip level. These indica-
tors are useful for easy check of signal levels and trim
adjustment (setup by use of the trim adjuster w).
indicator becomes green when a signal is approx. 30
dB below the clip level and changes to red when a sig-
nal is approx. 8 dB below the clip level. These indica-
tors are useful for easy check of signal levels and trim
adjustment (setup by use of the trim adjuster w).
u
Name Plates
Indicates the device name that is connected to an input
terminal.
terminal.
i
Input Faders
Adjusts the transmission level of input signals. The level
is rated when the input fader stands at 8.
is rated when the input fader stands at 8.
●
Mono Inputs 7 and 8
o
Phantom Power Switches [PHANTOM ON/OFF]
When this switch is toggled on, the phantom power
(+48 V) is supplied to a condenser microphone.
Therefore, toggling the switch on allows a condenser
microphone that requires external power supply to func-
tion by the use of the phantom power.
(+48 V) is supplied to a condenser microphone.
Therefore, toggling the switch on allows a condenser
microphone that requires external power supply to func-
tion by the use of the phantom power.
Cautions:
• Toggle the switch on only when using a condenser
microphone that requires external power supply.
• Refer to the operating instructions for a condenser
microphone when using it.
• Connect a condenser microphone after adjusting
the input fader to "0" in order to prevent noise occur-
rence.
rence.
!0
Trim Adjusters [INPUT 0 to 10]
Changes the input sensitivity stepwise.
MIC level:
–20 dB to –60 dB
Adjust the sensitivity so that optimal volume is gained
when the input fader stands at 8.
when the input fader stands at 8.
4
6
2
8
0
10
INPUT
ON
OFF
−
6
+
6
HIGH
−
15
+
15
LOW
MAIN 1 MAIN 2
SUB 1
SUB 2
4
6
2
8
0
10
INPUT
ON
OFF
−
6
+
6
HIGH
−
15
+
15
LOW
MAIN 1 MAIN 2
SUB 1
SUB 2
PHANTOM
PHANTOM
SEND
SGNL/PEAK
SEND
SGNL/PEAK
0
8
6
4
2
0
10
8
6
4
2
0
10
8
6
4
2
0
MONO 7
MONO 8
o
!0
−
10
+
10
0
INPUT
MAIN 1 MAIN 2
SUB 1
SUB 2
−
10
+
10
0
INPUT
MAIN 1 MAIN 2
SUB 1
SUB 2
−
10
+
10
0
INPUT
MAIN 1 MAIN 2
SUB 1
SUB 2
−
10
+
10
0
INPUT
MAIN 1 MAIN 2
SUB 1
SUB 2
SGNL/PEAK
SGNL/PEAK
SGNL/PEAK
SGNL/PEAK
0
8
6
4
2
0
10
8
6
4
2
0
10
8
6
4
2
0
10
8
6
4
2
0
ST 1
ST 2
ST 3
ST 4
!1
!2
!3
!4
!5
Click on the first or last page to see other WR-X22NL / WR-X22NH service manuals if exist.