Read Panasonic AG-DVX100AP / AG-DVX100AN / AG-DVX100AE / AG-DVX100EN / AG-DVC180AMC Service Manual online
ELE-13
4-3. REWRITE Saved Data
When Camera or VTR C.B.A. is replaced, It becomes impossible to adjustment or repairing during service
operation, rewrite the saved data which is stored in EEPROM as follows. And readjust.
operation, rewrite the saved data which is stored in EEPROM as follows. And readjust.
4-3-1. How to Rewrite All EEPROM data on Camera C.B.A.
1. Select “Camera Check menu” In the Main menu, and then press the “Enter” key.
2. Select “3. Read (Save) / Write All EEPROM datas” in the Camera check menu, and then press the “Enter”
2. Select “3. Read (Save) / Write All EEPROM datas” in the Camera check menu, and then press the “Enter”
key.
3. Select “10. Data write using stored file” in “3. Read (Save) / Write All EEPROM datas” menu, and then
press the “Enter” key.
4. Type the saved file name, and then press the “Enter” key.
5. Select “9. EEPROM ALL (2 Kbyte)”, and then press the “Enter” key.
6. The data can be written in EEPROM (IC307).
5. Select “9. EEPROM ALL (2 Kbyte)”, and then press the “Enter” key.
6. The data can be written in EEPROM (IC307).
4-3-2. How to Rewrite All EEPROM data on VTR C.B.A.
1. Select “Video Check menu” In the Main menu, and then press the “Enter” key.
2. Select “3. Read (Save) / Write All EEPROM datas” in the Video check menu, and then press the “Enter” key.
3. Select “6. Writing from the stored data files” in the “3. Read (Save) / Write All EEPROM datas” menu, and
2. Select “3. Read (Save) / Write All EEPROM datas” in the Video check menu, and then press the “Enter” key.
3. Select “6. Writing from the stored data files” in the “3. Read (Save) / Write All EEPROM datas” menu, and
then press “Enter” key.
4. Type the saved file name, and then press the “Enter” key.
5. Select “5. Write EEPROM (1024 byte)”, and then press the “Enter” key.
6. The data can be written in EEPROM (IC2008).
5. Select “5. Write EEPROM (1024 byte)”, and then press the “Enter” key.
6. The data can be written in EEPROM (IC2008).
4-4. EEPROM Data Upgrade Procedure.
EEPROM data can be changed individuality to upgrade. In case of EEPROM data have to changed for
improvement of some functions. Technical bulletin described address and data as indicated as below table.
-
-
VSI3983B (Ver12)
VSI3983D (Ver14)
Address 0542
1
Data 70
FF
Address 00ED
2
Data 12
14
NOTE:
Before up-grade the Camera or VTR EEPROM, be sure to save ALL EEPROM data into the personal
computer to avoid any accidental data loss. Regarding the saving method, refer to item 4-1 and 4-2 in this
section.
section.
4-4-1. CAMERA EEPROM upgrade procedure
1. Boot up EVR software and open the Camera check menu.
2. Select “2. EEPROM/RAM Editor” and press “ENTER” key.
2. Select “2. EEPROM/RAM Editor” and press “ENTER” key.
Click on the first or last page to see other AG-DVX100AP / AG-DVX100AN / AG-DVX100AE / AG-DVX100EN / AG-DVC180AMC service manuals if exist.