PT-VZ585N, PT-VW545N, PT-VX615N, PT-VZ580, PT-VW540, PT-VX610 (serv.man8) - Panasonic Projector Service Manual (repair manual)

pt-vz585n, pt-vw545n, pt-vx615n, pt-vz580, pt-vw540, pt-vx610 (serv.man8) service manual
Model
PT-VZ585N PT-VW545N PT-VX615N PT-VZ580 PT-VW540 PT-VX610 (serv.man8)
Pages
100
Size
21.47 MB
Type
PDF
Document
Service Manual
Brand
Device
Projector / LCD PROJECTOR
File
pt-vz585n-pt-vw545n-pt-vx615n-pt-vz580-pt-vw540-pt.pdf
Date

Read Panasonic PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man8) Service Manual online

Model No.
 
PT-VZ585N
PT-VW545N
PT-VX615N
 
PT-VZ580
PT-VW540
PT-VX610
 
LCD Projector
ORDER NO. VED1706655CE
Rev.-3 (2019-02)
For the block diagrams, schematic diagrams and parts list, refer to each separated booklet "Block and Schematic 
diagrams" and "Parts List" respectively.
 This manual is common to the models regardless of suffixes of the Model No. 
  The suffix of model no. shows the destination as the below.
  - "T" for Taiwan
  - "D" for India
  The model which does not have the destination suffix is for global model in common.
 Illustrations in this service manual
  Illustrations of the projector, screen, and other parts may vary from the actual product.
 
Illustrations of the projector with the power cord attached are only examples.
   The shape of the supplied power cords varies depending on the country where you purchased the product.
2
PREFACE
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
CAUTION
 
Precaution
  
Never use this projector at an altitude of 2 700m or higher.
    Using this projector at high altitude, consult your dealer or Authorized Service Center about preparations.
 
About lead free solder (PbF)
  
This projector is using the P.C.Board which applies lead free solder.
    Use lead free solder in servicing from the standpoint of antipollution for the global environment.
 
Notes:
  
•  Lead free solder: Sn-Ag-Cu (tin, silver and copper) has a higher melting point (approx. 217°C) than standard solder 
Typically the melting point is 30~40 °C higher. When servicing, use a high temperature soldering iron with temperature 
limitation function and set it to 370 ± 10 °C.
    •  Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx. 
600°C or higher).
    •  Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably 
use lead solder, use lead solder after removing lead free solder. Or be sure to heat the lead free solder until it melts 
completely, before applying lead solder.)
    •  After solder to double layered P.C Boards, check the component side for excess solder which may flow onto the oppo-
site side.
    About the identification of the lead free solder P.C.Board.
     For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the 
surface or the back of P.C.Board.
PbF
WARNING:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC 
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated 
in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to 
correct the interference at his own expense.
CAUTION:
Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.
There are special components used in this equipment which are important for safety. These parts are marked by 7 in the 
schematic diagram, circuit board diagrams, exploded views and replacement parts list. It is essential that these critical parts 
should be replaced with manufacturer’s specified parts to prevent shock, fire, or other hazards. Do not modify the original 
design without permission of manufacturer.
IMPORTANT SAFETY NOTICE
The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual.
Le technicien d'entretien doit lire et suivre les «Précautions de sécurité» et «Avis important de sécurité» dans ce manuel d'entretien.
7
 WARNING 
This service information is designed for experienced repair technicians only and is not designed for use by the general pub-
lic. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service 
a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any 
attempt to service or repair the product or products dealt with in this service information by anyone else could result in seri-
ous injury or death.
7
 
AVERTISSEMENT
Ce document d'entretien est destiné aux techniciens d'entretien expérimentés uniquement et n'est pas conçu pour une 
utilisation par le grand public. Il ne contient pas des avertissements ou des mises en garde pour aviser les non-techniciens 
des dangers potentiels lorsqu'ils tentent de réparer un produit. Les appareils alimentés par l'électricité doivent être révisés 
ou réparés uniquement par des techniciens professionnels expérimentés. Toute tentative d'entretenir ou de réparer le ou les 
produits traités dans ce document d'entretien par autrui peut entraîner des blessures graves ou la mort.
 
  WARNING : Use UV Radiation eye and skin protection during servicing.
 
   AVERTISSEMENT : Utilisez UV lumière oeil dioprotection et la protection de la peau lors de l'entretien.
CAUTION / MISE EN GARDE
 
Lithium Battery
 
  Risk of explosion if battery is replaced by an incorrect type.
    Replace only with the same of equivalent type recommended by the manufacturer.
    Dispose of used batteries according to the manufacturer’s instructions.
 
Batterie au lithium
    Risque d'explosion si la batterie est remplacée par un type incorrect.
    Remplacez-la uniquement par le même type ou le type équivalent recommandé par le fabricant.
    Jetez les batteries usagées conformément aux instructions du fabricant.
3
PREFACE
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
Notes on repairing
 
f
In case of fuse opening inside the projector, Do not turn the projector on just replacing the fuse with new one be-
cause there might be a possibility to have smoking or firing hazard. Turn it on after solving the main cause of fuse 
opening.
 
f
After repairing, confirm that the projector operates correctly.
 
f
Pay attention to handle the projector as customer's personal settings have been remaining inside the projector.  
Cautions when transporting
 
f
When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts.  
Doing so may damage the internal parts and result in malfunctions.
 
f
Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.
Cautions when installing
 
r
Do not set up the projector outdoors.
The projector is designed for indoor use only. 
 
r
Do not use under the following conditions.
 
f
Places where vibration and impacts occur such as in a car or vehicle: Doing so may damage the internal parts 
and result in malfunctions.
 
f
Location close to sea or where corrosive gas may occur: the projector may fall due to corrosion. Also, failure to do 
so may shorten the life of the components and result in malfunction.
 
f
Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare 
cases due to the heated air from the air exhaust port or the hot or cooled air. Make sure that the exhaust from the 
projector or other equipment, or the air from the air conditioner does not blow toward the front of the projector.
 
f
Places with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life of the 
luminous lamp, or result in deformation of the outer case due to heat, which may cause malfunction. Make sure to 
observe the operating temperature range of the projector.
 
f
Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
 
r
Be sure to ask a specialized technician or your dealer when installing the product to a 
ceiling.
This requires an optional ceiling mount bracket. Be sure to use the Projector Mount Bracket together with the ceiling 
mount bracket for high ceilings or low ceilings.
 
r
Ask a qualified technician or your dealer to install the cable wiring for DIGITAL LINK 
connection.(Only for PT-VZ585N,PT-VW545N,PT-VX615N)
Image and sound may be disrupted if cable transmission characteristics cannot be obtained due to inadequate
installation.
 
r
The projector may not work properly due to strong radio wave from the broadcast 
station or the radio.(Only for PT-VZ585N,PT-VW545N,PT-VX615N)
If there is any facility or equipment which outputs strong radio waves near the installation location, install the projec-
tor at a location sufficiently far from the source of the radio waves. Or, wrap the LAN cable connected to the <DIGI-
TAL LINK/LAN> terminal using a piece of metal foil or a metal pipe which is grounded at both ends.
 
r
Focus adjustment
The projection lens is thermally affected by the light from the light source, making the focus unstable in the period 
just after switching on the power. It is recommended that the images are projected continuously for at least 30 min-
utes before the focus is adjusted.
 
r
Do not install the projector at elevations of 2 700 m (8 858') or higher above sea level.
 
r
Do not use the projector in a location that the ambient temperature exceed 40 °C
 
(104 °F).
Using the projector in a location that the altitude is too high or the ambient temperature is too high may shorten the 
life of the components or result in malfunctions.
The upper limit of the operating temperature of the projector varies depending on the altitudes of the operating envi-
ronment. 
4
PREFACE
<VZ585N/VW545N/VX615N/VZ580/VW540/VX610>
When using it at altitudes below 1 200 m (3 937') above sea level: 0 °C (32 °F) ~ 40 °C (104 °F)  
When using it at altitudes between 1 200 m (3 937') and 2 700 m (8 858') above sea level: 0 °C (32 °F) ~ 30 °C 
(86 °F).
 
r
Do not tilt the projector or place it on its side.
Do not tilt the projector body more than approximately ±30 degrees longitudinally or ±15 degrees laterally. Over 
tilting may result in shortening the life of the components. 
Within 15°
Within 15°
Within 30°
Within 30°
Cautions when setting the projectors
 
f
Use the adjustable feet only for the  oor standing installation and for adjusting the angle. Using them for other 
purposes may damage the projector.
 
f
Do not stack the projectors.
 
f
Do not use the projector supported by its top.
 
f
Do not block the ventilation ports (intake and exhaust) of the projector.
20 - ENGLISH
Chapter 1   Preparation - Precautions for use
Page of 100
Display

Download Panasonic PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man8) Service Manual (Repair Manual)

Here you can read online and download Panasonic PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man8) Service Manual in PDF. PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man8) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic PT-VZ585N / PT-VW545N / PT-VX615N / PT-VZ580 / PT-VW540 / PT-VX610 (serv.man8) Projector. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.