Read Panasonic PT-TW342 / PT-TX402 / PT-TX312 (serv.man2) Service Manual online
-9-
Power indicator
<ON (G)/
STANDBY (R)>
Warning
indicator
<WARNING>
Status
Cause
Solution
Green
Lighting
Off
Projecting
--
--
Lighting
Lighting in red
The replacement time of
the lamp unit is displayed.
(Projecting)
the lamp unit is displayed.
(Projecting)
Is the lamp replacement
warning icon
displayed when turn on or turn
off the projector?
off the projector?
The indicator lights up when
the usage time of the lamp unit
reaches 6 000 hours (when
[Lamp control] is set to
reaches 6 000 hours (when
[Lamp control] is set to
[
(Eco 1)]).
Replace the lamp unit.
Lighting
Blinking in red
It have exceed the
replacement time of the lamp
unit and the projector is turned
off automatically.
replacement time of the lamp
unit and the projector is turned
off automatically.
The indicator blinks when the
usage time of the lamp unit
reaches 6 600 hours (when
[Lamp control] is set to
reaches 6 600 hours (when
[Lamp control] is set to
[
(Eco 1)]).
Blinking
Off
The power cord is plugged
and the lamp is turned off.
[Power management] is set to
[Ready].
and the lamp is turned off.
[Power management] is set to
[Ready].
--
--
Orange
Lighting
Off
The projector detects an
abnormal condition and
cannot be turned on.
(Warning)
abnormal condition and
cannot be turned on.
(Warning)
--
If the projector is turned off,
unplug the AC power cord
and contact the dealer.
and contact the dealer.
Lighting
Lighting
There is a problem in the
contrast shutter circuit for iris.
(Warning)
contrast shutter circuit for iris.
(Warning)
--
Turn off the projector,
unplug the AC power cord
and contact the dealer.
unplug the AC power cord
and contact the dealer.
Blinking
Blinking
The lamp or the power
supply for the lamp detects
an abnormal condition, the
projector cannot be turned on.
(Warning)
supply for the lamp detects
an abnormal condition, the
projector cannot be turned on.
(Warning)
Have you turned on the power
again immediately after turning
it off?
again immediately after turning
it off?
Wait a while until the
luminous lamp cools off,
and then turn on the power.
luminous lamp cools off,
and then turn on the power.
There is a problem in the lamp
circuit. Have the source voltage
been changed? (Drop)
circuit. Have the source voltage
been changed? (Drop)
Turn off the projector, and
unplug the AC power cord,
and consult your dealer.
unplug the AC power cord,
and consult your dealer.
Blinking
Off
Internal temperature is high.
(Warning)
When the internal temperature
rises further and the air filter
warning icon
(Warning)
When the internal temperature
rises further and the air filter
warning icon
*1
is displayed on the screen,
after a while the projector can
be turned off automatically.
after a while the projector can
be turned off automatically.
Is the air intake/exhaust port
blocked?
Is the room temperature high?
Is the air filter unit clogged?
Is the air filter unit clogged?
Remove any objects that
are blocking the air intake/
exhaust port.
exhaust port.
Install the projector in a
location with an ambient
temperature of 5 °C
temperature of 5 °C
(41 °F) to 40 °C (104 °F).
Do not use the projector at
Do not use the projector at
high altitudes of 3 000 m
(9 843') or higher above
sea level.
(9 843') or higher above
sea level.
Clean the air filter unit or
replace it.
*1 Regardless of the time which is set in [Expand] → [Filter counter], the air filter warning icon
is displayed due to the
internal temperature rising, and it will be displayed 10 seconds every five minutes if the temperature does not go down.
Note
If the warning indicator <WARNING> persists to light or blink after taking these measurements such as turn off the projector,
unplug the power cord, please contact your dealer for repair services.
If the power indicator <ON(G)/STANDBY(R)> persists to light or blink in orange after taking these measurements such as turn
off the projector, unplug the power cord, please contact your dealer for repair services.
Circuit protections
Click on the first or last page to see other PT-TW342 / PT-TX402 / PT-TX312 (serv.man2) service manuals if exist.