Read Panasonic PT-RZ575 (serv.man2) Service Manual online
INF-4
SECTION 1 SERVICE INFORMATION
< RZ575 >
1.4 Remote controls
1
2
6
5
7
8
9
16
18
19
19
17
10
11
4
3
13
5
12
14
15
15
23
24
20
21
22
21
22
Front
Top
Bottom
1 Power <v/b> button
Sets the projector to the state where the projector is turned
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
Sets the projector to projection mode when the power is
switched off (standby mode).
2 Remote control indicator
Blinks if any button in the remote control is pressed.
3 Lens buttons (<FOCUS>, <SHIFT>)
Adjusts the projection lens.
The <ZOOM> button is not used with the projector.
4 <MENU> button/<RETURN> button/<ENTER> button/
asqw
buttons
Used to navigate through the menu screen.
asqw
asqw
buttons are also used to enter the password in
[SECURITY] or enter characters.
5 <VOL-> button/<VOL+> button
Adjusts the volume of audio output.
6 <DEFAULT> button
6 <DEFAULT> button
Resets the content of the sub-menu to the factory default.
7 Input selection buttons (<HDMI 1>, <HDMI 2>, <DIGITAL
LINK>, <COMPUTER 1/2>, <VIDEO>, <DVI-D>)
Switches the input signal to project.
8 Number (<0> - <9>) buttons
Used for entering an ID number or a password in a multiple
projector environment.
9 <ON SCREEN> button
Switches the on-screen display function on (display) or
off (hide).
10 <ID ALL> button
Used to simultaneously control all the projectors with a
single remote control in a multiple projector environment.
11 <ECO> button
Displays the setting screen relating to ECO management.
12 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image.
[PROGRESS] is displayed while in automatic adjustment.
13 <FUNCTION> button
Assigns a frequently used operation as a shortcut button.
14 <TEST PATTERN> button
Displays the test pattern.
15 <ID SET> button
15 <ID SET> button
Sets the ID number of the remote control in a multiple
projector environment.
16 <SCREEN ADJ> button
Used to correct the distortion of the projected image.
17 <FREEZE> button
Used when pausing the image and turning off the audio.
18 <P IN P> button
Switches the picture in picture function setting.
19 <STATUS> button
19 <STATUS> button
Displays the projector information.
20 <SHUTTER> button
Used when temporarily turning off the image and audio.
21 <MUTE> button
Used when temporarily turning off the audio.
22 <ASPECT> button
22 <ASPECT> button
Switches the aspect ratio of the image.
23 Remote control signal transmitter
24 (Not available with this projector)
23 Remote control signal transmitter
24 (Not available with this projector)
Note
f
When operating the remote control by directly pointing at the remote control signal receiver of the projector, operate the remote control
within a distance approximately 30 m (98'5") from the remote control signal receiver. The remote control can control at angles of up to ±30°
vertically and horizontally, but the effective control range may be reduced.
f
If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
f
The signal will be reflected off the screen. However, the operating range may be limited from light reflection loss due to the screen material.
f
If the remote control signal receiver directly receives strong light, such as fluorescent light, the remote control may not operate properly. Use
it in a place distant from the light source.
f
The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.
Click on the first or last page to see other PT-RZ575 (serv.man2) service manuals if exist.