Read Sharp CD-SW300H (serv.man2) User Guide / Operation Manual online
AC INPUT
ANTENNA
FM
75 OHMS
AM
GND
Left speaker
1
Accessories
Remote control × 1
TINSEA140AWZZ
0
0
6C R KI 1
3
System connections
AM loop aerial × 1
FM aerial × 1
2
Remote control battery installation
1
Open the battery cover.
2
Insert the batteries as shown.
3
Close the cover.
Use 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
Batteries are not included.
Wall socket
(AC 230 - 240 V, 50 Hz)
(AC 230 - 240 V, 50 Hz)
FM aerial
AM loop aerial
Right speaker
Black
Red
Black
Purple
Red
Subwoofer
Subwoofer light-up wire
MODEL
CD-SW300H
MINI COMPONENT SYSTEM
4
Turn on your system
The first time the unit is plugged in, the unit will enter the demonstration mode.
You will see words scroll.
1
Press the X-BASS(SURROUND)/DEMO button to cancel the demonstration mode.
2
Press the ON/STAND-BY button to turn the power on.
This quick Start Guide will help you to correctly install and
operate your system.
operate your system.
CD-SW300E QG
2/14/06, 3:31 PM
1
Listening to a cassette tape
TAPE 1
TAPE 2
Listening to the radio
Listening to a CD or MP3/WMA disc
1
Press the CD button.
2
Press the 1 button and within 5 seconds, press the button to
open the disc tray 1.
open the disc tray 1.
3
Place the disc on the disc tray 1, label side up.
4
Press the button to close the disc tray 1.
5
You can place discs on trays 2 - 5 by following steps 2 - 4.
6
Press the
/
button to start playback.
12 cm (5”)
8 cm (3”)
1
Press the TUNER (BAND) button repeatedly to select the desired
frequency band (FM or AM).
frequency band (FM or AM).
2
Press the TUNING ( or ) button to tune in to the desired station.
When the TUNING ( or ) button is pressed for more than 0.5 sec-
onds, scanning will start automatically and the tuner will stop at the
first receivable broadcast station.
When the TUNING ( or ) button is pressed for more than 0.5 sec-
onds, scanning will start automatically and the tuner will stop at the
first receivable broadcast station.
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the “ST” indicator.
Press the TUNER (BAND) button to display the “ST” indicator.
“
” will appear when an FM broadcast is in stereo.
1
Open the cassette compartment by
pushing the area marked “ ”.
pushing the area marked “ ”.
2
Load a cassette into the TAPE 1 compartment
or TAPE 2 compartment with the side to be
played facing towards you.
or TAPE 2 compartment with the side to be
played facing towards you.
3
Press the TAPE (1
2) button to select the cassette you want to
listen to.
4
Press the /
(TAPE ) button to start playback.
FM stereo mode indicator
FM stereo receiving indicator
If trouble occurs
When this product is subjected to strong external interference (me-
chanical shock, excessive static electricity, abnormal supply voltage
due to lightning, etc.) or if it is operated incorrectly, it may malfunction.
chanical shock, excessive static electricity, abnormal supply voltage
due to lightning, etc.) or if it is operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1.
1.
Set the unit to the stand-by mode and turn the power on again.
2.
Note:
If neither operation above restores the unit, clear all the memory by
resetting it.
If neither operation above restores the unit, clear all the memory by
resetting it.
Clearing all the memory (reset)
1.
Press the ON/STAND-BY button to enter the power stand-by
mode.
mode.
2.
Whilst pressing down the button and the
7
7
7
7
7 button, press
the TUNER (BAND) button until “CLEAR ALL” appears.
Caution:
This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD programme.
This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD programme.
Maintenance
Routine maintenance is required for continued optimum perfor-
mance, refer to the operation manual.
mance, refer to the operation manual.
CD-SW300E QG
2/14/06, 3:31 PM
2
Display
