Read Panasonic PT-FZ570 / PT-FW530 / PT-FX500 (serv.man4) Service Manual online
INF-2
SECTION 1 SERVICE INFORMATION
<FZ570/FW530/FX500>
1. The name of each part
1. 1. Projector body
Chapter 1 Preparation — About your projector
26 - ENGLISH
Attention
f
Do not drop the remote control.
f
Avoid contact with liquids or moisture.
f
Do not attempt to modify or disassemble the remote control.
f
Please observe the following contents that are described on the back of the remote
control unit (see the right picture).
1. Do not use a new battery together with an old battery.
2. Do not use unspecified batteries.
3. Make sure the polarities (+ and -) are correct when inserting the batteries.
f
In addition, please read the contents that are related to batteries in the "Read this first!".
Caution label at the back of the remote control
Note
f
When operating the remote control by directly pointing the remote control signal receiver of the projector, operate the remote control at
a distance approx. 30 m (98'5") or shorter from the remote control signal receiver. The remote control can control at angles of up to ±30°
vertically and horizontally, but the effective control range may be reduced.
f
If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
f
The signal will be reflected off the screen. However, the operating range may be limited from light reflection loss due to the screen material.
f
If the remote control signal receiver directly receives strong light, such as fluorescent light, the remote control may not operate properly. Use
it in a place distant from the light source.
f
The power indicator <ON(G)/STANDBY(R)> will blink if the projector receives a remote control signal.
Projector body
1
7
6
2 3 4 5
8
9
10
8
11
13
14
16
15
19
17
11
18
12
WARNING
Keep your hands and other objects away from the air
exhaust port.
f
Keep your hands and face away.
f
Do not insert your fingers.
f
Keep heat-sensitive objects away.
Heated air from the air exhaust port can cause burns, injury, or
deformations.
1 Remote control signal receiver (front)
2 Power indicator <ON(G)/STANDBY(R)>
2 Power indicator <ON(G)/STANDBY(R)>
Displays the status of the power.
3 Lamp indicator <LAMP>
Displays the status of the lamp.
4 Temperature indicator <TEMP>
Displays the status of the internal temperature.
5 Filter indicator <FILTER>
Displays the status of the air filter unit.
6 Focus lever (Front)
Zoom lever (Back)
7 Lens shift lever
Adjusts the projection position.
8 Adjustable feet
Adjusts the projection angle.
9 Speaker
10 Projection lens
11 Air exhaust port
12 Remote control signal receiver (rear)
11 Air exhaust port
12 Remote control signal receiver (rear)
1. 请勿把旧电池和新电池一起使用。
2. 请勿使用不合规格的电池。
3. 确保电池安装正确。
原产地：中国
1.Do not use old battery with new one.
2.Do not use batteries other than the
2.Do not use batteries other than the
type specified.
3.Be sure the batteries are inserted properly.
3.Be sure the batteries are inserted properly.
Made in China
Front
Side
Rear
Projection direction
Chapter 1 Preparation — About your projector
ENGLISH - 27
13 <AC IN> terminal
Connect the supplied power cord.
14 <MAIN POWER> switch
Turns off/on the main power.
15 Connecting terminals
16 Security slot
16 Security slot
This security slot is compatible with the Kensington security
cables.
17 Control panel
18 Air ilter cover
18 Air ilter cover
The air filter units are inside.
19 Air intake port
22
20
21
19
20 Burglar hook port
Attaches a burglar prevention cable, etc.
21 Luminance sensor
Measures the brightness of the installation environment. When
the daylight view function is set to [AUTO], the vividness of the
image is automatically corrected.
22 Lamp cover
The lamp unit is inside.
Attention
f
Do not block the ventilation ports (intake and exhaust) of the projector.
r
Control panel
6
3
5
1
2
3
4
1 Power <v/b> button (v standby/b power on)
Sets the projector to the state where the projector is switched
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in the projection mode. Also starts
projection when the power is switched off (standby mode).
2 <MENU> button/<ENTER> button/asqw buttons
Used to navigate through the menu screen.
Returns to the previous menu when a sub-menu is displayed.
Also used to enter a password in [SECURITY] or enter
characters.
3 <VOL-> button/<VOL+> button
Adjusts the volume of audio output.
4 <AV MUTE> button
Used when temporarily turning off the image and audio.
5 <INPUT SELECT> button
Switches the input signal to project.
6 <AUTO SETUP> button
Automatically adjusts the screen display position
when projecting the image.
Bottom
Top
Projection direction
Click on the first or last page to see other PT-FZ570 / PT-FW530 / PT-FX500 (serv.man4) service manuals if exist.