Read Panasonic PT-EZ580 / PT-EZ580L / PT-EZ580D / PT-EZ580LD / PT-EW640 / PT-EW640L / PT-EW640D / PT-EW640LD / PT-EX610 / PT-EX610L / PT-EX610D / PT-EX610LD Service Manual online
INF-16
SECTION 1 SERVICE INFORMATION
4. External Controls
4. 1. Control through Serial terminal
SERIAL terminals which are on the side of the projector conform to RS-232C standard. This projector can be controlled by a
PC which is connected as shown below. Also SERIAL OUT terminal is provided to enable plural projector control.
PC which is connected as shown below. Also SERIAL OUT terminal is provided to enable plural projector control.
4. 1. 1. Connection
When connecting directly
Communication cable (straight)
D-Sub 9p (Male)
D-Sub 9p (Female)
Projector Connection terminals
Computer
When connecting with DIGITAL LINK compatible devices
DIGITAL LINK
DIGITAL LINK
Communication cable (straight)
LAN cable (straight)
D-Sub 9p (Male)
D-Sub 9p (Female)
Projector Connection terminals
DIGITAL LINK Connection terminals
Computer
Note
• The destination of [RS-232C] must be set according to the connection method.
• When connecting by a DIGITAL LINK compatible device, set the [PROJECTOR SETUP] menu → [ECO MANAGEMENT]
→ [STANDBY MODE] to [NORMAL] to control the projector in standby mode. When [STANDBY MODE] is set to [ECO], the
projector cannot be control during standby.
projector cannot be control during standby.
4. 1. 2. Pin assignments and signal names
D-Sub 9-pin (female)
Outside view
Pin No.
Signal name
Details
(9)
(6)
(5)
(1)
(1)
–
NC
(2)
TXD
Transmitted data
(3)
RXD
Received data
(4)
–
NC
(5)
GND
Earth
(6)
–
NC
(7)
CTS
Connected internally
(8)
RTS
(9)
–
NC
4. 1. 3. Communication conditions (Factory default)
Signal level
RS-232C compliant
Sync. method
Asynchronous
Baud rate
9 600 bps
Parity
None
Character length
8 bits
Stop bit
1 bit
X parameter
None
S parameter
None
4. 1. 4. Communication condition setting
1. Press the [MENU] button on the projector or remote controller.
Go to Main menu --> Projector setup. In sub menu,
Go to Main menu --> Projector setup. In sub menu,
Select "RS-232C" and press [ENTER] button.
2. Select communication condition by pressing ▲ ▼ button.
Set it with pressing
t u button.
3. Press MENU button 3 times and return to regular display.
ȲȳȒȓȒȣ
ȩȮȰȵȴȀȳȥȬȥȣȴ
ȩȮȰȵȴȀȳȥȬȥȣȴ
ȢȡȵȤȲȡȴȥ
ȮȯȮȥ
șȖȐȐ
ȰȲȯȪȥȣȴȯȲ
ȰȡȲȩȴȹ
ȭȥȮȵȀȳȥȬȥȣȴ
ȣȨȡȮȧȥ
Click on the first or last page to see other PT-EZ580 / PT-EZ580L / PT-EZ580D / PT-EZ580LD / PT-EW640 / PT-EW640L / PT-EW640D / PT-EW640LD / PT-EX610 / PT-EX610L / PT-EX610D / PT-EX610LD service manuals if exist.