Read Panasonic PT-EZ580 / PT-EZ580L / PT-EZ580D / PT-EZ580LD / PT-EW640 / PT-EW640L / PT-EW640D / PT-EW640LD / PT-EX610 / PT-EX610L / PT-EX610D / PT-EX610LD (serv.man2) Service Manual online
INF-12
SECTION 1 SERVICE INFORMATION
1. SELF CHECK
Self-diagnosing information Displays.
2. FLICKER ADJUST
• Perform the flicker adjustment
* Please refer to SECTION 3 (Adjustments) for the procedure. This adjustment should be performed after replacing the LCD
block or A-P.C. Board.
3. POWER OFF MESSAGE
• Setting of the shutter function with standby operation
- SHUTTER KEEP: When pushing the standby key while the shutter mode is on, the projector keeps the shutter mode on
and sets into standby mode.
- SHUTTER OPEN: When pushing the standby key while the shutter mode is on, the projector opens the shutter and displays
the "Power OFF confirmation message". (Default setting)
4. CONVERGENCE
• When the ingredient of each R/G/B color deviation, revise it electrically.
Specifically, please refer to chapter SECTION 3 (Adjustments)
5. MODEL
This setting is necessary when the A-P.C. Board is replaced with new one.
• If you can copy EEPROM data from old A-P.C. Board, this setting is unnecessary.
• This model setting is effective after power restart.
6. CLOG SENSOR CALIBRATION
• This is to calibrate the clog sensor circuit. This calibration is necessary when the [A]-P.C Board, EEPROM (IC1416) or
[M2]- P.C. Board is replaced.
• Refer to the chapter SECTION 3 (Adjustments) for the procedure.
7. WINDOW EDGE CALIBRATION (Factory use only)
• This is to setup the Window Edge Correction function On or Off.
- ON: Enable the Window Edge Correction (not memorized)
- OFF: Disable the Window Edge Correction function stop (Default setting)
8. SGM (Factory use only)
• To switch the LCD panel gamma characteristic
- ON: Enable the SGM function
- OFF: Disable the SGM function (Default setting)
(1) – MODEL: Model no. / S/N: Serial no.
(2) – MAIN: Main software version / NT: Network software
version
(3) – SUB: Sub software version / DIGITAL LINK: Digital
Link software version
(4) – Emulate setting • Version
(5) – Status of correction data in the memories
G-SAVED: Gamma correction data
U-SAVED: Color shading correction data
BG means no data saved
(6) – Intake air temperature check (Celsius/Fahrenheit)
(7) – Exhaust air temperature check (Celsius/Fahrenheit)
(8) – Air flow sensor check
(Sensor reading value/AD value/ Correction value)
(9) – LAMP check (Cumulative usage time/ON-OFF)
(10) – Fan check (1: normal /0:stop)
ȯȫȀȦȡȮȀȀȑȑȑȑȀȑȑȑȑ
ȬȣȤȈȲȉ
ȬȣȤȈȧȉ
ȬȣȤȈȢȉ
ȬȡȭȰȑ
ȬȡȭȰȒ
ȰȯȷȥȲ
ȥȸȵȡȳȴ
(11) –Angle sensor check (Horizontal angle/Vertical angle)
(12) – Pressure sensor check
(Air pressure value[hPa]/Sensor temperature)
(13) – Iris check
(14) – Shutter check (Opening and shutting number of times
[Failed number of times])
6(/)&+(&.
02'(/(=61$%
0$,117
68%',*,7$//,1.
(08/$7('()$8/7
2.*6$9('
2.86$9('
2.$,57(03
2.2877(03
2.$,5)/2:
2./$03+021
2.)$1
2.$1*/(6(1625+9
2.$706(1625
2.,5,6
2.6+877(5>@
* The word "OK" of Items (6) to (14) will be indicated in red
if the projector had shutdown due to abnormality last time.
(1)
(2)
(3)
(4)
(2)
(3)
(4)
(5)
(6)
(6)
(7)
(8)
(9)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
Click on the first or last page to see other PT-EZ580 / PT-EZ580L / PT-EZ580D / PT-EZ580LD / PT-EW640 / PT-EW640L / PT-EW640D / PT-EW640LD / PT-EX610 / PT-EX610L / PT-EX610D / PT-EX610LD (serv.man2) service manuals if exist.