Read Panasonic PT-DZ6710U / PT-DZ6710E / PT-DZ6700U / PT-DZ6700E / PT-DW6300US / PT-DW6300ES / PT-D6000US / PT-D6000ES / PT-DZ6710UL / PT-DZ6710EL / PT-DZ6700UL / PT-DZ6700EL / PT-DW6300ULS / PT-DW6300ELS / PT-D6000ULS / PT-D6000ELS / PT-D6000ELK / PT-D6000EK / PT-DW630 Service Manual online
7. ERROR OSD
Displays the lamp status with OSD when you do not see the status LED lights because the rear projection, etc.
8. MODEL
Set it when the A-P.C.Board is replaced.
·
If replacing A-P.C.Board (assembly), set MODEL.
* Never set it to a model name different from the model that installs the new A-P.C.Board. If a different model name is set,
it becomes impossible to output normal pictures after the next startup.
it becomes impossible to output normal pictures after the next startup.
* When a new A-P.C.Board is installed without maintenance of adjustment data, it is required to adjust the color wheel.
9. ACF
Executes ACF setting/operation.
·
FILTER SETUP: Sets the interval time of automatic rewinding of the filter.
·
ROLL: Rewinds the filter once compulsorily.
10. CLOG SENSOR CALIBRATION
Execute the sensor calibration when EEPROM (IC3103 or IC3104) / A-P.C.Board or Airflow sensor (CF1302) is replaced.
* Make the main unit to the assembled state without fail, set the projector to the floor installation, and calibrate.
* If the projector installed at an elevation of 1 400 m or higher sea level, be sure to set the HIGH ALTITUDE MODE sub-menu
in PROJECTOR SETUP menu to ON, and attempt the calibration.
in PROJECTOR SETUP menu to ON, and attempt the calibration.
When OK is selected and ENTER button is pressed, the calibration is executed.
·
When the calibration is started, the screen becomes whole magenta.
·
While calibrating, all lamps will light (DUAL mode).
·
Do not switch OFF the projector while calibrating.
·
When the magenta screen will disappear in approx. 15 minutes and it returns to the normal screen, the calibration is
completed.
completed.
·
Turn the POWER switch OFF and turn ON it again, then confirm whether to operate normally.
4.3.2. Ye MODULATE Addition
When the PICTURE MODE menu is displayed, it is enabled to be adjusted with the ENTER button.
·
ON: Validates Ye MODULATE function.
·
OFF: Invalidates Ye MODULATE function.
4.3.3. ADVANCED MENU Addition
The following 4 items are added to the ADVANCED MENU.
1. FRAME LOCK
When the input signal is RGB, FRAME LOCK is added.
2. 480i SD
When non-standard signal of 480i/576i is inputted (AV amplifier, etc.), synchronization might be disordered according to
connected equipment. In this case, set 480i SD to ON.
connected equipment. In this case, set 480i SD to ON.
3. 480p OS
When 480p/576p is received, aliasing noise (longitudinal striated beat noise) might be generated according to connected
equipment. In this case, set 480p OS to ON. However, the resolution decreases a little.
equipment. In this case, set 480p OS to ON. However, the resolution decreases a little.
12
PT-DZ6710U / PT-DZ6710E / PT-DZ6700U / PT-DZ6700E / PT-DW6300US / PT-DW6300ES / PT-D6000US / PT-D6000ES
Click on the first or last page to see other PT-DZ6710U / PT-DZ6710E / PT-DZ6700U / PT-DZ6700E / PT-DW6300US / PT-DW6300ES / PT-D6000US / PT-D6000ES / PT-DZ6710UL / PT-DZ6710EL / PT-DZ6700UL / PT-DZ6700EL / PT-DW6300ULS / PT-DW6300ELS / PT-D6000ULS / PT-D6000ELS / PT-D6000ELK / PT-D6000EK / PT-DW630 service manuals if exist.