Read Panasonic DP-8020E / DP-8020P / DP-8016P (serv.man2) Service Manual online
116
SEP 2006
Ver. 1.1
DP-8020E/8020P/8016P
3.7.5.
User Authentication Function Confirmation (Specified Destinations only)
If your customer requires User Authentication, and/or Via Fax Server, setup the feature(s) by referring to the
Operating Instructions (For User Authentication).
Operating Instructions (For User Authentication).
3.7.6.
Notice after installing the HDD option
After the Hard Disk Drive Unit is installed, to prevent a Scan Disk Function from being performed (similar
to Windows OS when the power is abruptly interrupted), it is important to follow the step sequence below
when turning OFF the Power Switch on the machine.
to Windows OS when the power is abruptly interrupted), it is important to follow the step sequence below
when turning OFF the Power Switch on the machine.
1. If the machine is in the "ENERGY SAVER (Shutdown Mode)", you may turn the Power Switch on
the Right Side of the machine to the OFF position. If it is not in the "ENERGY SAVER (Shutdown
Mode)", continue to step 2 below.
Mode)", continue to step 2 below.
2. Press "FUNCTION", and "ENERGY SAVER" keys simultaneously first.
3. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk Drive
3. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk Drive
Unit, and advances into “ENERGY SAVER MODE”.
4. Turn the Power Switch on the Right side of the machine to the OFF position.
5. Unplug the AC Power Cord. (During a Lightning Storm, to prevent electrocution disconnect the
5. Unplug the AC Power Cord. (During a Lightning Storm, to prevent electrocution disconnect the
Telephone Line Cable first before unplugging the AC Power Cord, if the Fax option installed.)
6. After finishing the installation of the Hard Disk Drive, please go over the above Power Down
procedure with the customer to avoid the Scan Disk Function from being performed (indicated by
SCANNING HARD DISK message on the display), and customer inquiries related to abrupt Power
Off.
SCANNING HARD DISK message on the display), and customer inquiries related to abrupt Power
Off.
7. Reconnect the Telephone Line Cable if it was disconnected.
3.7.7.
Firmware Emergency Recovery
The easiest method to recover the firmware in an Emergency Recovery routine is to either use the Local
Firmware Update Tool software by selecting the Independent File method, or using the Master Firmware
Flash Card method (2 Flash Cards required).
Firmware Update Tool software by selecting the Independent File method, or using the Master Firmware
Flash Card method (2 Flash Cards required).
Whichever method you select, it is easier to restore the machine's firmware to the Standard (AAV) Type
first as it only requires 2 files to bring the machine to initial working condition. (Install the files in this
order: SC, and SPC).
first as it only requires 2 files to bring the machine to initial working condition. (Install the files in this
order: SC, and SPC).
After recovering, if optional PCL, or PS/PCL firmware is required, use the Network Firmware Update
Tool, or the Local Firmware Update Tool to update the firmware to the required level.
Tool, or the Local Firmware Update Tool to update the firmware to the required level.
If the unit does not boot up properly, follow the steps below:
1. Turn the power Off (use the power switch on the right side of the unit).
- Before proceeding to the next step, you must prepare either the Local Firmware Update Tool, or
create the Master Firmware Flash Cards (read the appropriate sections first).
- If using the Master Firmware Card, insert the Master Firmware Flash Cards in the unit.
2. Turn the power On while holding the “ENERGY SAVER” key.
3. When the green lamp on the front panel turns On, release the “ENERGY SAVER” key.
3. When the green lamp on the front panel turns On, release the “ENERGY SAVER” key.
- If using the Master Firmware Card, the unit will start updating the Firmware code files
automatically.
The unit is now ready to accept the firmware code from the USB Port, or Master Firmware Card.
Repeat the above steps if there are additional firmware code files to be updated.
Repeat the above steps if there are additional firmware code files to be updated.
Click on the first or last page to see other DP-8020E / DP-8020P / DP-8016P (serv.man2) service manuals if exist.