Read Panasonic KV-S8147 / KV-S8127 / KV-S8150 / KV-S8130 / KV-S8120 Service Manual online
111
F40 (Hopper error)
30
00
00
00 1. Hopper does not work properly.
1. Check following mechanism by carrying out
“Hopper drive” test in Sec.10.3.7.
Motor rotation, Drive belt and the engaging
with the Hopper Drive gear train and the
rack.
Motor rotation, Drive belt and the engaging
with the Hopper Drive gear train and the
rack.
2. Check the following connection and
soldering condition on each connector.
a. CN5081 (HOPPER HOME SENSOR
Board) to CN3301 (LOWER RELAY
Board)
b. CN3304 (LOWER RELAY Board) to CN18
(CONTROL Board)
c. CN5090 (HOPPER UPPER LIMIT
SENSOR Board) to CN3001 (UPPER
RELAY Board)
d. CN3004 (UPPER RELAY Board) to CN19
(CONTROL Board)
a. CN5081 (HOPPER HOME SENSOR
Board) to CN3301 (LOWER RELAY
Board)
b. CN3304 (LOWER RELAY Board) to CN18
(CONTROL Board)
c. CN5090 (HOPPER UPPER LIMIT
SENSOR Board) to CN3001 (UPPER
RELAY Board)
d. CN3004 (UPPER RELAY Board) to CN19
(CONTROL Board)
3. Check the soldering condition of the IC5080
(HOPPER HOME SENSOR Board) and
IC5090 (HOPPER UPPER LIMIT SENSOR
Board) and its surrounding circuits.
IC5090 (HOPPER UPPER LIMIT SENSOR
Board) and its surrounding circuits.
4. Check the soldering condition of the IC32
(CONTROL Board) and its surrounding.
5. Replace faulty parts or related parts.
2. Pressure Sensor does not work. 1. Check the assembly of the Pressure sensor.
Check the connection of status of the
harness to the CN5091 (HOPPER UPPER
LIMIT SENSOR Board).
harness to the CN5091 (HOPPER UPPER
LIMIT SENSOR Board).
2. Check the following connection and
soldering condition on each connector.
a. CN5090 (HOPPER UPPER LIMIT
SENSOR Board) to CN3001 (UPPER
RELAY Board)
b. CN3304 (LOWER RELAY Board) to CN19
(CONTROL Board)
a. CN5090 (HOPPER UPPER LIMIT
SENSOR Board) to CN3001 (UPPER
RELAY Board)
b. CN3304 (LOWER RELAY Board) to CN19
(CONTROL Board)
3. Replace faulty parts or related parts.
F42 (DFP Roller was
not in the home posi-
tion.)
not in the home posi-
tion.)
32
00
00
00 1. DFP Pressure Motor does not
work properly.
Refer to Section 7 of Error Codes U12.
2. DFP Pressure Motor control cir-
cuit does not work properly
Refer to Section 8 of Error Codes U12.
3. DFP Pressure Motor does not
drive the DFP cam shaft which
controls DFP Roller's position.
controls DFP Roller's position.
1. Check the ADF mechanism. (See Sec.7.4.)
2. Execute “DFP pressure drive” in Sec.
2. Execute “DFP pressure drive” in Sec.
10.3.7. to check the ADF mechanism.
4. DFP Home Detector does not
work correctly.
1. Execute “Key/Sensor” test in Sec. 10.3.7.
to check the detector condition.
2. Check whether the tip of the DFP Cam Shaft
interrupts the detector.
3. Check the following connections and
soldering condition on each connector.
a. CN5050 (DFP HOME SENSOR Board) to
CN3301 (LOWER RELAY Board)
b. CN3304 (LOWER RELAY Board) to
CN18 (CONTROL Board)
a. CN5050 (DFP HOME SENSOR Board) to
CN3301 (LOWER RELAY Board)
b. CN3304 (LOWER RELAY Board) to
CN18 (CONTROL Board)
4. Check the following signals of CONTROL
Board.
CN18-29th pin and IC32-4th pin : 5 V
(when the tip of the DFP Cam Shaft
interrupts IC5050 (DFP Home Sensor) on
the DFP HOME Board)
CN18-29th pin and IC32-4th pin : 5 V
(when the tip of the DFP Cam Shaft
interrupts IC5050 (DFP Home Sensor) on
the DFP HOME Board)
5. Check the soldering condition of IC32 on the
CONTROL Board and repair it
6. Replace faulty parts or boards.
Error Code
ST1 ST2 ST3 ST4
Possible Cause
Recommended action
Remarks
Click on the first or last page to see other KV-S8147 / KV-S8127 / KV-S8150 / KV-S8130 / KV-S8120 service manuals if exist.