Read Panasonic KV-S7065C (serv.man4) Service Manual online
Error Code
Possible Cause
Check Point
Remarks
Classified Code
ST1
ST2
ST3
ST4
U23
(Double feed
error)
(Double feed
error)
1C
00
xx
00
2. Double
feed does
not occur.
feed does
not occur.
Double Feed Detector
(R) does not work
properly.
(R) does not work
properly.
1.
Execute Double Feed test in Sec.9.3.6 to
check the detector condition.
check the detector condition.
2.
Check whether the receiver alignment is
proper.
proper.
3.
Check the following connection and
soldering condition on each connector.
soldering condition on each connector.
a.
Double Feed Detector (R) to CN5001
(OUTER CONVEYOR RELAY Board)
(OUTER CONVEYOR RELAY Board)
b.
CN5004 (OUTER CONVEYOR
RELAY Board) to CN1014 (CONTROL
Board)
RELAY Board) to CN1014 (CONTROL
Board)
4.
Check the following parts’ soldering
condition to repair it.
condition to repair it.
a.
CONTROL Board
IC1024 (117
th
pin)
b.
OUTER CONVEYOR RELAY Board
IC5002, IC5004, Q5002, Q5003, and
the surrounding circuit
the surrounding circuit
5.
Check the following signals on the
OUTER CONVEYOR RELAY Board.
OUTER CONVEYOR RELAY Board.
a.
IC5002-7
th
pin: DC12 V
b.
IC5004-7
th
pin
→ See Fig.10.2.5.
6.
Replace faulty parts or boards.
U30 (Door open)
20
00
00
00
1. ADF Door or Exit Door is not
closed properly.
closed properly.
1.
Shut the door properly.
2. Door SW (Micro switch) does not
work correctly.
work correctly.
1.
Execute Key / Sensor in Sec.9.3.6 to
check the door switch mechanical
condition between the door and micro
switch.
check the door switch mechanical
condition between the door and micro
switch.
2.
Check the connection between the door
switches (ADF Door Switch, Exit Door
Switch) and CN5028 on the POWER
RELAY Board.
switches (ADF Door Switch, Exit Door
Switch) and CN5028 on the POWER
RELAY Board.
3.
Replace a faulty cable or switch.
3. Monitor circuit to check the door
ON/OFF condition is broken.
ON/OFF condition is broken.
1.
Check the following connection and
soldering condition on each connector.
soldering condition on each connector.
a.
CN5036 (POWER RELAY Board) to
CN4005 (DRIVE Board)
CN4005 (DRIVE Board)
b.
CN4001 (DRIVE Board) to CN1007
(CONTROL Board)
(CONTROL Board)
2.
Check the following parts’ soldering
condition to repair it.
condition to repair it.
a.
DRIVE Board
Q4007, R4001, D4001
b.
CONTROL Board
IC1024-120
th
pin
3.
Check the following signals.
→ +24VIL (D4001 Cathode): 24 V
→ DOOR1 (CN4001-34
→ DOOR1 (CN4001-34
th
pin): 0 V
4.
Replace faulty parts or boards.
F17
(GA-IMG SDRAM
error)
(GA-IMG SDRAM
error)
87
xx
00
00
Access error to SDRAM (IC2018,
IC2019, IC2020, IC2021) on the
INTERFACE Board
IC2019, IC2020, IC2021) on the
INTERFACE Board
1.
Check the soldering condition of the Gate
Array (IC2047) on the INTERFACE Board
to repair it.
Array (IC2047) on the INTERFACE Board
to repair it.
2.
Check the soldering condition of the
SDRAM (IC2018, IC2019, IC2020,
IC2021) on the INTERFACE Board to
repair it.
SDRAM (IC2018, IC2019, IC2020,
IC2021) on the INTERFACE Board to
repair it.
3.
Replace faulty parts or INTERFACE
Board.
Board.
121
KV-S7065CSERIES
Click on the first or last page to see other KV-S7065C (serv.man4) service manuals if exist.