Read Panasonic UF-490 (serv.man2) Service Manual online
107
301
XMT
RCV
RCV
System fault.
Software problem occurred. (SC PCB)
331
XMT
C
8-minutes timer error.
(Germany only)
(Germany only)
400
XMT
B
T1 timer (35±5 sec.) elapsed
without detecting 300 bps signal.
without detecting 300 bps signal.
Wrong number is dialed and the START
button is pushed.
Telephone line is disconnected while
dialing.
SC PCB (Modem) is defective.
Receiver is defective. (It may only be
transmitting CED)
button is pushed.
Telephone line is disconnected while
dialing.
SC PCB (Modem) is defective.
Receiver is defective. (It may only be
transmitting CED)
401
XMT
B
DCN was returned from receiver
while transmitter is waiting for CFR
or FTT.
while transmitter is waiting for CFR
or FTT.
Your machine's ID Number is not
programmed.
Possible incompatibility or incorrect
Password.
programmed.
Possible incompatibility or incorrect
Password.
402
XMT
B
DCN was returned from receiver
while transmitter is waiting for
NSF/DIS.
while transmitter is waiting for
NSF/DIS.
Receiver working in non-CCITT mode
only. (Possible incompatibility)
only. (Possible incompatibility)
403
RCV
(Polling)
B
Transmitter had no polling function. "POLLED=ON" (polling XMT ready) is
not set at the transmitter.
Document to be transmitted is not
placed at the transmitter.
Document to be transmitted is not
placed at the transmitter.
404
XMT
B
Transmitter sent NSS (or DCS)
followed by TCF three times, but
the receiver did not respond. (CFR
or FTT is usually returned)
followed by TCF three times, but
the receiver did not respond. (CFR
or FTT is usually returned)
Receiver is defective. (Modem, etc.)
SC PCB is defective.
Receiver disconnects line during first
NSS (or DCS) is transmitted.
SC PCB is defective.
Receiver disconnects line during first
NSS (or DCS) is transmitted.
405
XMT
B
Transmitter received FTT after it
transmitted TCF at 2400bps.
Received RTN after
communicating at 2400 bps.
transmitted TCF at 2400bps.
Received RTN after
communicating at 2400 bps.
Line quality is poor. (TCF is damaged
due to line noise)
Receiver is defective. (Modem, etc.)
SC PCB is defective.
due to line noise)
Receiver is defective. (Modem, etc.)
SC PCB is defective.
407
XMT
D
Transmitter received no response
after it transmitted post message,
such as EOP, MPS, EOM, etc...or
received DCN.
after it transmitted post message,
such as EOP, MPS, EOM, etc...or
received DCN.
Receiver is defective. (No paper, paper
jamming, etc.)
Receiver ceased receiving because of
excessive error. (Line quality is poor)
SC PCB (Modem) is defective.
jamming, etc.)
Receiver ceased receiving because of
excessive error. (Line quality is poor)
SC PCB (Modem) is defective.
408
XMT
D
Transmitter received RTN after it
transmitted EOP, MPS, or EOM.
transmitted EOP, MPS, or EOM.
Receiver receives data with error. (Line
quality is poor)
Receiver is defective. (Modem, etc.)
SC PCB is defective.
quality is poor)
Receiver is defective. (Modem, etc.)
SC PCB is defective.
409
XMT
D
Transmitter receives PIN after it
transmitted a post message, such
as EOP, MPS, EOM, etc.
transmitted a post message, such
as EOP, MPS, EOM, etc.
Receiver receives data with error due to
poor line quality, and receiving operator
requests voice contact.
Receiver is defective. (Modem, etc.)
SC PCB is defective.
poor line quality, and receiving operator
requests voice contact.
Receiver is defective. (Modem, etc.)
SC PCB is defective.
410
RCV
D
Received DCN while waiting for
post command. (EOP, MPS, EOM,
etc.)
post command. (EOP, MPS, EOM,
etc.)
Interface or line is faulty.
Transmitter is defective.
Transmitter is defective.
411
RCV
(Polling)
B
Received DCN after transmitting
NSC.
NSC.
Transmitter is not ready for polling
communication.
Password does not match between
transmitter and receiver.
communication.
Password does not match between
transmitter and receiver.
Fax Information Codes
Code
Mode
Phase
Description of Problem
Cause
Click on the first or last page to see other UF-490 (serv.man2) service manuals if exist.