Read Sharp AR-F151 (serv.man9) Service Manual online
CODE: 00ZARF151/A1E
DIGITAL COPIER
AR-150
AR-155
AR-155
MODEL
AR-F151
[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
[ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . 2 - 1
[ 3 ] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . 3 - 1
[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . 4 - 1
[ 5 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . 5 - 1
[ 6 ] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . 6 - 1
[ 7 ] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . 7 - 1
[ 8 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
[ 9 ] SIMULATION, FAX SOFTWARE SWITCH,
TROUBLE CODES . . . . . . . . . . . . . . . . . . . . . 9 - 1
[10] USER PROGRAM . . . . . . . . . . . . . . . . . . . . . . 10 - 1
[11] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . 11 - 1
[12] CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . 12 - 1
CONTENTS
Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
(AR-F151)
AR-F151
[7] DISASSEMBLY AND ASSEMBLY
Before disassembly, be sure to disconnect the power cord for safety.
The disassembly and assembly procedures are described for the fol-
lowing sections:
1. High voltage section
2. Operation panel section
3. Optical section
4. Fusing section
5. Tray paper feed/transport section
6. Manual paper feed section
7. Rear frame section
8. Power section
9. SPF section
10. 2nd cassette section
11. DUP motor section
12. Reverse roller section
13. RSPF section
14. FAX MCU PWB section
15. FAX-SPF section
The disassembly and assembly procedures are described for the fol-
lowing sections:
1. High voltage section
2. Operation panel section
3. Optical section
4. Fusing section
5. Tray paper feed/transport section
6. Manual paper feed section
7. Rear frame section
8. Power section
9. SPF section
10. 2nd cassette section
11. DUP motor section
12. Reverse roller section
13. RSPF section
14. FAX MCU PWB section
15. FAX-SPF section
1. High voltage section
A. List
No.
Part name Ref.
1
Transfer charger unit
2
Charger wire
B. Disassembly procedure
(1) Press the side cover open/close button and open the side cover.
(2) Push up the lock pawls (2 positions) of the side cover, and remove
the transfer charger.
C. Assembly procedure
For assembly, reverse the disassembly procedure.
D. Charger wire cleaning
(1) Remove the charger cleaner from the manual paper feed unit.
2)
1)
1)
Transfer
charger
charger
Lock pawl rear
Lock pawl front
1)
2)
1)
AR-F151
7 – 1
(2) Set the charger cleaner to the transfer unit, and move it reciprocal-
ly a few times in the arrow direction shown in the figure below.
E. Charger wire replacement
(1) Remove the TC cover and remove the screw.
(2) Remove the spring and remove the charger wire.
(3) Install a new charger wire by reversing the procedures (1) and (2).
(2) Remove the spring and remove the charger wire.
(3) Install a new charger wire by reversing the procedures (1) and (2).
At that time, be careful of the following items.
●
The rest of the charger wire must be within 1.5mm.
●
The spring hook section (charger wire winding section) must be
in the range of the projection section.
in the range of the projection section.
●
Be careful not to twist the charger wire.
2. Operation panel section
A. List
No.
Part name Ref.
1
Operation panel unit
2
Operation PWB
B. Disassembly procedure
(1) Remove the screws (4 pcs.), the harness, and the operation panel
unit.
(2) Remove the screws (3 pcs.) and the PWB holder.
(3) Remove the screws (3 pcs.) and the operation PWB.
(3) Remove the screws (3 pcs.) and the operation PWB.
1)
2)
3)
4)
1mm
1.5mm
1)
1)
2)
3)
Charger wire
Protrusion
1)
2)
3)
1)
1)
4)
3)
1)
2)
3)
3)
Note that there are 13 pawls
AR-F151
7 – 2
C. Assembly procedure
For assembly, reverse the disassembly procedure
3. Optical section
A. List
NO.
Part name Ref.
1
Copy lamp unit
2
Copy lamp
3
Lens unit
B. Disassembly procedure
(1) Remove the parts as shown below.
(2) Remove the screws (2pcs.), and remove the copy lamp unit from
the mirror base drive wire.
(3) Pull the copy lamp unit toward you to remove the harness.
(4) Remove the screw (4 pc) and remove the cover.
2)
1)
9)
1)
3)
4)
6)
8)
10)
7)
5)
Hook
1)
2)
3)
1)
2)
2)
3)
3)
4)
4)
1)
2)
3)
AR-F151
7 – 3