Read Panasonic KX-FT76RU-B Service Manual online
Bit No.
DIS/DTC
Standard setting
DCS
34
Recording width capability 1216 picture elements along
scan line length of 151 ± mm 1%
scan line length of 151 ± mm 1%
0
Middle 1216 elements of 1728 picture elements
35
Recording width capability 864 picture elements along
scan line length of 107 ± mm 1%
scan line length of 107 ± mm 1%
0
Middle 864 elements of 1728 picture elements
36
Recording width capability 1728 picture elements along
scan line length of 151 ± mm 1%
scan line length of 151 ± mm 1%
0
Invalid
37
Recording width capability 1728 picture elements along
scan line length of 107 ± mm 1%
scan line length of 107 ± mm 1%
0
Invalid
38
Reserved for future recording width capabilities.
0
39
Reserved for future recording width capabilities.
0
40
Extend field
1
Extend field
41
Semi super time / mm
1
42
Semi super time / mm
0
43
Super time
0
44
Inch
0
45
mm
1
46
MSC/SF
0
47
Select Polling
0
48
EXT
0
Note 1 - Standard facsimile units conforming to T.2 must have the following capability: Index of cooperation (IOC)=264.
Note 2 - Standard facsimile units conforming to T.3 must have the following capability: Index of cooperation (IOC)=264.
Note 3 - Standard facsimile units conforming to T.4 must have the following capability: Paper length=297 mm.
Signal
Identification Signal Format
Function
Training 1
———————
A fixed pattern is transmitted to the receiving side at a speed
(2400 to 9600 bps) designated by DCS, and the receiving side
optimizes the automatic equalizer, etc., according to this signal.
(2400 to 9600 bps) designated by DCS, and the receiving side
optimizes the automatic equalizer, etc., according to this signal.
TCF
(Training Check)
(Training Check)
———————
Sends 0 continuously for 1.5 seconds at the same speed as the
training signal.
training signal.
CFR
(Confirmation to Receive)
(Confirmation to Receive)
X0100001
Notifies the sending side that TCF has been properly received. If
TCF is not properly received, FTT (Failure To Train) X0100010 is
relayed to the sender. The sender then reduces the transmission
speed by one stage and initiates training once again.
TCF is not properly received, FTT (Failure To Train) X0100010 is
relayed to the sender. The sender then reduces the transmission
speed by one stage and initiates training once again.
Training 2
———————
Used for reconfirming the receiving side like training 1.
Image Signal
Refer to the next page.
———————
RTC
(Return to Control)
(Return to Control)
———————
Sends 12 bits (0...01 × 6 times) to the receiver at the same speed
as the image signal and notifies completion of transmission of the
first sheet.
as the image signal and notifies completion of transmission of the
first sheet.
EOP
(End of Procedure)
(End of Procedure)
X1110100
End of one communication
MCF
(Message Confirmation)
(Message Confirmation)
X0110001
End of 1 page reception
DCN
(Disconnect)
(Disconnect)
X1011111
Phase E starts.
MPS
(Multi-Page Signal)
(Multi-Page Signal)
X1110010
Completion of transmission of 1 page. If there are still more
documents to be sent, they are output instead of EOP. After MCF
reception, the sender transmits an image signal of the second
sheet.
documents to be sent, they are output instead of EOP. After MCF
reception, the sender transmits an image signal of the second
sheet.
PRI-EOP
(Procedural Interrupt-EOP)
(Procedural Interrupt-EOP)
X1111100
If there is an operator call from the sender, it is output after RTC.
PIP
(Procedural Interrupt Positive)
(Procedural Interrupt Positive)
X0110101
This is output when an operator call is received.
127
KX-FT76RU-B
