Read Panasonic KX-FM131CE Service Manual Simplified online
3.4. SERVICE FUNCTION TABLE
Change from original pages 103~105 (2.4.4 SERVICE FUNCTION TABLE)
Code
Function
Set Value
Effective Range
Default
Remarks
501
Pause time set
X 100 msec
001~600
50
502
Recall time set
X 10 msec
01~99
10
503
Dial speed select
1:10 pps 2:20 pps
1, 2
1
510
VOX TIME
1:6 sec 2:4 sec
1, 2
1
511
Vox sense
1:HIGH 2:LOW
1, 2
1
When the TAM dose not stop
recording the ICM because noise is
detected on the telephone line,
change this setting to “LOW“.
recording the ICM because noise is
detected on the telephone line,
change this setting to “LOW“.
520
CED frequency select
1:2100 Hz 2:1100 Hz
1, 2
1
See the Symptom/
Countermeasure Table for long
distance and international calls in
2.3.3.3.1. Defective facsimile
section.
Countermeasure Table for long
distance and international calls in
2.3.3.3.1. Defective facsimile
section.
521
International mode select
1:ON 2:OFF
1, 2
1
See the Symptom/
Countermeasure Table for long
distance and international calls in
2.3.3.3.1. Defective facsimile
section.
Countermeasure Table for long
distance and international calls in
2.3.3.3.1. Defective facsimile
section.
522
Auto standby select
1:ON 2:OFF
1, 2
1
The resolution reverts to the
default when transmission is
complete.
default when transmission is
complete.
523
Receive equalizer select
1:0 km 2:1.8 km 3:3.6
km 4:7.2 km
km 4:7.2 km
1~4
1
When the telephone station is far
from the unit or reception cannot
be performed correctly, adjust
accordingly.
from the unit or reception cannot
be performed correctly, adjust
accordingly.
524
Transmission equalizer select
1:0 km 2:1.8 km 3:3.6
km 4:7.2 km
km 4:7.2 km
1~4
1
When the telephone station is far
from the unit or transmission
cannot be performed correctly,
adjust accordingly.
from the unit or transmission
cannot be performed correctly,
adjust accordingly.
533
Setting the number of times that
massage transfer is redialed.
massage transfer is redialed.
00~99
00~99
3
Selects the number of times that
message transfer is redialed (not
including the first dialing).
message transfer is redialed (not
including the first dialing).
534
Setting the message transfer/pager
call redial interval
call redial interval
001~999 sec
001~999
65
Sets the interval of message
transfer/pager call redial.
transfer/pager call redial.
550
Memory clear: To reset the value to the default one, except the top margin (853)
and left margin (854).
and left margin (854).
"START" input"
552
DTMF single tone test
1:ON 2:OFF
1, 2
2
See 2.5. TEST FUNCTIONS.
553
Monitor on FAX communication
select
select
1: OFF 2:PHASE B
3:ALL
3:ALL
1~3
1
554
Modem test
See 2.5. TEST FUNCTIONS.
555
Scan check
See 2.5. TEST FUNCTIONS.
556
Motor test
0
See 2.5. TEST FUNCTIONS.
557
LED test
See 2.5. TEST FUNCTIONS.
558
LCD test
See 2.5. TEST FUNCTIONS.
559
Document jam detection select
1:ON 2:OFF
1, 2
1
See 2.2.1. Paper Jam.
561
KEY test
See 2.5. TEST FUNCTIONS.
570
BREAK % select
1:61% 2:67%
1, 2
1
Sets the % break of pulse dialing
according PBX.
according PBX.
571
ITS auto redial time set
X number of times
00~99
10
Selects the number of times that
ITS is redialed (not including the
first dial).
ITS is redialed (not including the
first dial).
572
ITS auto redial line disconnection
time set
time set
X second
001~999
65
Sets the interval of ITS redialing.
573
Remote turn-on ring number set
X number of rings
01~99
15
Sets the number of rings before
the unit starts to receive a
document in the TEL mode.
the unit starts to receive a
document in the TEL mode.
580
TAM continuous tone detection
1:ON 2:OFF
1, 2
1
ON : Stops TAM operation when
Dial tone, etc. are detected.
Dial tone, etc. are detected.
590
FAX auto redial time set
X number of times
00~99
5
Selects the number of redial times
during FAX communication (not
including the first dial).
during FAX communication (not
including the first dial).
591
FAX auto redial time disconnection
time set
time set
X second
001~999
65
Sets the FAX redial interval during
FAX communication.
FAX communication.
592
CNG transmit select
1: OFF 2:ALL
3:AUTO
3:AUTO
1~3
2
Lets you select the CNG output
during FAX transmission. ALL:
CNG is output at phase A. AUTO:
CNG is output only when automatic
dialing is performed. OFF: CNG is
not output at phase A.
during FAX transmission. ALL:
CNG is output at phase A. AUTO:
CNG is output only when automatic
dialing is performed. OFF: CNG is
not output at phase A.
13
KX-FM131CE
Click on the first or last page to see other KX-FM131CE service manuals if exist.