Read Panasonic DMC-GF1CPP / DMC-GF1CEB / DMC-GF1CEC / DMC-GF1CEG / DMC-GF1CGC / DMC-GF1CGH / DMC-GF1CGK / DMC-GF1CGN / DMC-GF1KPP / DMC-GF1KEB / DMC-GF1KEC / DMC-GF1KEG / DMC-GF1KGC / DMC-GF1KGH / DMC-GF1KGK / DMC-GF1KGN / DMC-GF1PP / DMC-GF1EB / DMC-GF1EC / DMC-GF1EG / Service Manual online
ORDER NO. DSC0909058CE
B26
Digital Camera/Lens Kit/Body
Model No.
DMC-GF1CPP
DMC-GF1CEB
DMC-GF1CEC
DMC-GF1CEG
DMC-GF1CGC
DMC-GF1CGH
DMC-GF1CGK
DMC-GF1CGN
DMC-GF1KPP
DMC-GF1KEB
DMC-GF1KEC
DMC-GF1KEG
DMC-GF1KGC
DMC-GF1KGH
DMC-GF1KGK
DMC-GF1KGN
DMC-GF1PP
DMC-GF1EB
DMC-GF1EC
DMC-GF1EG
DMC-GF1GC
DMC-GF1GH
DMC-GF1CEB
DMC-GF1CEC
DMC-GF1CEG
DMC-GF1CGC
DMC-GF1CGH
DMC-GF1CGK
DMC-GF1CGN
DMC-GF1KPP
DMC-GF1KEB
DMC-GF1KEC
DMC-GF1KEG
DMC-GF1KGC
DMC-GF1KGH
DMC-GF1KGK
DMC-GF1KGN
DMC-GF1PP
DMC-GF1EB
DMC-GF1EC
DMC-GF1EG
DMC-GF1GC
DMC-GF1GH
2
Vol.1
Colour
(K)...........Black Type
(S)...........Silver Type (only EB/EG/GC/GH/GK)
(R)...........Red Type (except GN)
(W)..........White Type (only EG/GH)
(S)...........Silver Type (only EB/EG/GC/GH/GK)
(R)...........Red Type (except GN)
(W)..........White Type (only EG/GH)
TABLE OF CONTENTS
PAGE
PAGE
1 Safety Precautions -----------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.) --------3
1.4. How to Discharge the E. Capacitor on Flash
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.) --------3
1.4. How to Discharge the E. Capacitor on Flash
Sub P.C.B. ---------------------------------------------------4
2 Warning --------------------------------------------------------------5
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------5
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------5
2.3. Caution for AC Cord (For EB/GC/GH) ----------------6
2.4. How to Replace the Lithium Battery -------------------7
2.4. How to Replace the Lithium Battery -------------------7
3 Service Navigation------------------------------------------------8
3.1. Introduction --------------------------------------------------8
3.2. Important Notice --------------------------------------------8
3.3. General Description About Lead Free Solder
3.2. Important Notice --------------------------------------------8
3.3. General Description About Lead Free Solder
(PbF) -------------------------------------------------------- 12
3.4. How to Define the Model Suffix (NTSC or PAL
model)------------------------------------------------------- 13
4 Specifications ---------------------------------------------------- 16
5 Location of Controls and Components------------------ 17
6 Service Mode ----------------------------------------------------- 35
5 Location of Controls and Components------------------ 17
6 Service Mode ----------------------------------------------------- 35
6.1. Error Code Memory Function ------------------------- 35
7 Troubleshooting Guide---------------------------------------- 37
7.1. Checking Method of Body and
Interchangeable Lens ----------------------------------- 37
7.2. Checking Method of Drive Circuit -------------------- 41
8 Service Fixture & Tools --------------------------------------- 43
8.1. Service Fixture and Tools ------------------------------ 43
8.2. Clean Box -------------------------------------------------- 44
8.3. Service Position ------------------------------------------ 45
8.2. Clean Box -------------------------------------------------- 44
8.3. Service Position ------------------------------------------ 45
9 Disassembly and Assembly Instructions --------------- 46
9.1. Disassembly Flow Chart-------------------------------- 46
9.2. PCB Location---------------------------------------------- 46
9.3. Disassembly Procedure -------------------------------- 47
9.4. Disassembly and Assemble Procedure for the
9.2. PCB Location---------------------------------------------- 46
9.3. Disassembly Procedure -------------------------------- 47
9.4. Disassembly and Assemble Procedure for the
Lens (H-H020) -------------------------------------------- 56
9.5. Disassembly and Assemble Procedure for the
Lens (H-FS014045)-------------------------------------- 59
10 Measurements and Adjustments -------------------------- 61
10.1. Matrix Chart for Replaced Part and Necessary
Adjustment ------------------------------------------------- 61
11 Maintenance ------------------------------------------------------ 63
11.1. Notice in external cleaning----------------------------- 63
11.2. General description (Lens cleaning:
11.2. General description (Lens cleaning:
Interchangeable Lens/H-H020) ----------------------- 64
11.3. General description (Lens cleaning:
Interchangeable Lens/H-FS014045)---------------- 67
3
1 Safety Precautions
1.1.
General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essen-
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
shock hazards.
1.2.
Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 M
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 M
Ω and 5.2 MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
reading must be infinity.
1.3.
Leakage Current Hot Check
(See Figure 1.)
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5 k
Ω, 10 W resistor, in parallel with a 0.15 μF
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 k
Ω/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the volt-
age at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equiva-
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure. 1
4
1.4.
How to Discharge the E. Capacitor on Flash Sub P.C.B.
CAUTION:
1. Be sure to discharge the E. Capacitor on FLASH SUB P.C.B..
2. Be careful of the high voltage circuit on FLASH SUB P.C.B. when servicing.
2. Be careful of the high voltage circuit on FLASH SUB P.C.B. when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k
Ω /5W).
(An equivalent type of resistor may be used.)
3. Put the resistor between both terminals of E. Capacitor on FLASH SUB P.C.B. for approx. 5 seconds.
4. After discharging confirm that the E. Capacitor voltage is lower than 10V using a voltmeter.
4. After discharging confirm that the E. Capacitor voltage is lower than 10V using a voltmeter.
Fig. F1