Read Panasonic WV-PS154 / WV-PS15 Service Manual online
– 5 –
WV-PS154/WV-PS15
2.1. Tuning Frequency Adjustment
Test Point : TP100 (DC VOLTAGE-1)
Main Board
TP300 (DC VOLTAGE-2)
Main Board
TP500 (DC VOLTAGE-3)
Main Board
TP700 (DC VOLTAGE-4)
Main Board
For WV-PS154
TP100 (DC VOLTAGE)
Main Board
For WV-PS15
Adjusts :
L100 (TUNING FREQ-1)
Main Board
L300 (TUNING FREQ-2)
Main Board
L500 (TUNING FREQ-3)
Main Board
L700 (TUNING FREQ-4)
Main Board
For WV-PS154
L100 (TUNING FREQ)
Main Board
For WV-PS15
Turn OFF the Power On/Off switch.
Turn the VR100 (for 1-ch) to fully counterclockwise posi-
tion.
Turn on the Power On/Off switch, set the FM Standard
Signal Generator so that the output level becomes
Turn the VR100 (for 1-ch) to fully counterclockwise posi-
tion.
Turn on the Power On/Off switch, set the FM Standard
Signal Generator so that the output level becomes
A
dBm.
Connect the Digital voltmeter to TP100 (for 1-ch) .
Adjust L100 (for 1-ch) so that the DC Voltage on the
Digital Voltmeter becomes 4.3
Adjust L100 (for 1-ch) so that the DC Voltage on the
Digital Voltmeter becomes 4.3
±
0.1V.
Note : Make sure the unit has sufficiently cooled off
before turning ON the power.
Also, adjust the unit within one minute after turn-
ing ON the power.
Also, adjust the unit within one minute after turn-
ing ON the power.
Confirm that the DC Voltage is 4.5
±
0.1V at 30 minutes
after turned ON the Power On/Off switch.
For WV-PS154, the same as above, adjust L300 (2-ch) ,
L500 (3-ch) and L700 (4-ch) so that the DC Voltage
becomes 4.3
For WV-PS154, the same as above, adjust L300 (2-ch) ,
L500 (3-ch) and L700 (4-ch) so that the DC Voltage
becomes 4.3
±
0.1V in similar way of L100 (1-ch).
2.3. Mute Level Adjustment
Test Point : Audio Output Connector (AUDIO OUT)
JK103 on the Main Board
Adjusts :
VR101 (MUTE LEVEL-1)
Main Board
VR301 (MUTE LEVEL-2)
Main Board
VR501 (MUTE LEVEL-3)
Main Board
VR701 (MUTE LEVEL-4)
Main Board
For WV-PS154
VR101 (MUTE LEVEL)
Main Board
For WV-PS15
Set the FM Standard Signal Generator so that the output
level becomes (
level becomes (
A
-21) dBm.
While observing the Audio Output Level, rotate VR101
(for 1-ch) in the counterclockwise direction and adjust
until the Audio Output Level drops a 1dBV range from the
point where it starts to drop.
Change the output level to (
(for 1-ch) in the counterclockwise direction and adjust
until the Audio Output Level drops a 1dBV range from the
point where it starts to drop.
Change the output level to (
A
-24) dBm from (
A
-21)
dBm.
Confirm that the Audio Output Level is less than
Confirm that the Audio Output Level is less than
−
16dBV.
For WV-PS154, the same as above, adjust VR301 (2-ch) ,
VR501 (3-ch) and VR701 (4-ch) in similar way of VR101 (1-
ch) .
VR501 (3-ch) and VR701 (4-ch) in similar way of VR101 (1-
ch) .
3. Vertical Frequency Adjustment
Test Point : TP106 (V.FREQ)
Main Board
Adjusts :
CT1 (V.FREQ)
Main Board
Note : This adjustment should be done at 10 minutes after
turned ON the Power On/Off Switch.
Connect the Frequency Counter to TP106.
(Ground terminal is TP101 on the Main Board.)
Adjust CT1 so that the Vertical Frequency becomes
204800.000
(Ground terminal is TP101 on the Main Board.)
Adjust CT1 so that the Vertical Frequency becomes
204800.000
±
1.024Hz.
2.2. Audio Output Level Adjustment
Test Point : Audio Output Connector (AUDIO OUT)
JK103 on the Main Board
Adjusts :
VR102 (AUDIO OUTPUT-1)
Main Board
VR302 (AUDIO OUTPUT-2)
Main Board
VR502 (AUDIO OUTPUT-3)
Main Board
VR702 (AUDIO OUTPUT-4)
Main Board
For WV-PS154
VR102 (AUDIO OUTPUT)
Main Board
For WV-PS15
Set the FM Standard Signal Generator so that the output
level becomes
level becomes
A
dBm.
Adjust VR102 (for 1-ch) so that the Audio Output Level
becomes
becomes
−
10
±
0.5dBV.
For WV-PS154, the same as above, adjust VR302 (2-ch) ,
VR502 (3-ch) and VR702 (4-ch) so that the Audio Output
Level becomes
VR502 (3-ch) and VR702 (4-ch) so that the Audio Output
Level becomes
−
10
±
0.5dBV in similar way of VR102 (1-ch) .
Click on the first or last page to see other WV-PS154 / WV-PS15 service manuals if exist.