WV-CW860, WV-CW864E - Panasonic Video Monitoring Service Manual (repair manual). Page 13

– 9 –

8

Peel the RS485 Setting Label which covers switch holes

on top of the camera.

8

Set the DIP switches (SW1, 2) on the Switch Board as

shown in Fig. 4-5.

8

Stick the label as it was.

8

The adjustment should be done after 30 minutes warm-up.

8

Set the Logarithmic Gray Scale Chart.

8

Incident light of 1 400 lx ± 50 lx on the Logarithmic Gray

Scale Chart.

8

Aim the Camera at the Logarithmic Gray Scale Chart.

8

Set the Camera by the E.V.R. Adjustment Kit so that the

Logarithmic Gray Scale Chart becomes full picture on the

Underscanned Colour Video Monitor.

8

Adjust the Lens Focus by the E.V.R. Adjustment Kit to

obtain correct focal point.

8

The adjustments should be done with this Standard

Picture, unless otherwise specified.

SW1

AC24VONL

Y

RS485Setting

S TART

REAR

SW

2

ON

1

2

3

4

5

6

7

8

ON

1

2

3

4

CAMERA TOP VIEW

RS485 Setting Label

SWITCH VIEW

SW2
4-bit DIP SW
#1 : ON, #2-#4 : OFF

SW1
8-bit DIP SW
#1-#8 : OFF

■

8

Connect the Camera Output Cable of WV-CW860/WV-

CW864E to the Camera Input Connector of the E.V.R.

Adjustment Kit.

8

Connect the E.V.R. Adjustment Kit to IBM PC/AT type

using the Standard Straight RS-232C cable.

8

Insert new disk containing DOS Operating System and the

E.V.R. Adjustment program into IBM PC/AT and turns on

the Power Switch of IBM PC/AT.

8

At the prompt, type RADJ2 CW860E and press the

ENTER key, then the initial menu page as shown in Fig.5-

1 will be displayed.

8

Press the SAVE (F5) key of the Computer, and the

Computer will ask you for the file name.

8

Type  xxxxxxxx.EV2 0000 0EFF. Give an appropriate file

name for xxxxxxxx within 8 letters, but do not use

CW860E. 

8

Press the ENTER key.

8

This saving procedure is recommended to keep the

current adjustment status of the Camera.

8

Press the LOAD (F1) key and type CW860E.EV2 and

press the ENTER key for presetting the adjustment of the

Camera.

∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗

M E N U

PANASONIC  EVR  ADJUSTMENT  SYSTEM   (C)MCI  Co.   CCTV  PRODUCT: CW860   EEPROM: 0

<CONTENTS>      TD322 17.73447+–40Hz
<INSTRUCTION> PLEASE  CHOOSE  MENU  DATA  BY  ARROW-KEY

LOAD(F1)

QUIT(F3)

SAVE(F5)

P A L

1. SC FREQUENCY
2. LL PHASE FOR AC type (50Hz)
3. HI CLIP LEVEL
4. PEDESTAL
5. ALC DC
6.1. VIDEO OUT GAIN (L)
6.2. VIDEO OUT GAIN (H)
7. MANUAL IRIS (A)
8. MANUAL IRIS (B)
9. MANUAL IRIS (C)
10. MANUAL IRIS (D)
11.1. BURST LEVEL R
11.2. BURST LEVEL B
11.3. BURST PHASE R
11.4. BURST PHASE B
12.1. WB 3200K MANU OFFSET R
12.2. WB 3200K MANU OFFSET B
13.1. WB 6500K ATW LIMIT R
13.2. WB 6500K ATW LIMIT B
14.1. 3200K R_GAIN

14.2. 3200K B_GAIN
14.3. 3200K R–MATRIX
14.4. 3200K B–MATRIX
15.1. 5100K R_GAIN
15.2. 5100K B_GAIN
15.3. 5100K B–MATRIX
16. HIGHLIGHT CHROMA CLIP

P a g e   ( 1 / 1 )