WV-CU550B - Panasonic Video Monitoring Service Manual Simplified (repair manual). Page 4

– 2 –

{

CAM: Used for camera selection. To select a camera,

enter the desired camera number with the Numeric
keys, and then press the CAM key.

SET: This key, in combination with the Numeric keys, is

used to enter numeric input, such as operator ID and
password.
It is also used to execute the currently highlighted
selection and to enter a submenu in the Setup Menu
of the Matrix Switcher.

}

These keys are used for numeric input into the system,
such as the camera and monitor number, sequence
number, preset position, etc.

q

MON: This key is used to select a monitor.

To select a monitor, press the corresponding
Numeric keys, followed by the MON key.

ESC: This key is used to escape from the currently high-

lighted selection on the Setup Menu of the Matrix
Switcher.

Pressing this key, while the Alternate (ALT) indicator is
on, will display the video that is connected to the Monitor
Input (MONITOR IN) Connector on the WV-PB5504AE
Video Output Board.

w

STOP: Pauses a sequence that is being run on the

active monitor.

SLOW: For fine pan/tilt control, move the joystick while

holding down the SLOW button.

e

When a sequence running in forward direction has been
paused with the Stop button, pressing this button will
move the sequence one frame to the next step (in for-
ward run direction). If the sequence was running in
reverse direction, the button will move the sequence one
frame to the next step (in reverse run direction).
This button is also used to select a camera. Pressing this
button will replace the currently selected camera with the
next higher camera number, if the active monitor is in
Spot mode.

r

When a sequence running in forward direction has been
paused with the Stop button, pressing this button will
move the sequence one frame to the previous step (in
forward run direction). If the sequence was running in
reverse direction, the button will move the sequence one
frame to the previous step (in reverse run direction).
This button is also used to select a camera. Pressing this
button will replace the currently selected camera with the
next lower camera number, if the active monitor is in
Spot mode.

t

These buttons toggle the auxiliary switches in the
Receiver on and off.
The auxiliary switches can be used, for example, to acti-
vate equipment connected to the receiver, such as lamps
and buzzers.

y

This button activates the alternate function of dual-func-
tion control buttons.
Pressing this button will toggle the indicator on the but-
ton on and off.

u

This button is used to run a selected Program or Tour
Sequence in forward direction on the active monitor.
It also restarts a sequence forward from the step that
was previously paused by pressing the Stop button.

i

This button is used to restart a sequence backward from
the step that was previously paused by pressing the
Stop button.

o

This button cancels an activated alarm. To cancel an
alarm, first select the alarmed monitor(s), then press the
ACK RESET button once for alarm acknowledgment
(the indicator on the button blinks rapidly), and finally
press it again for alarm reset (the indicator goes off).
After  an alarm acknowledgment, pressing this button
while the Alternate (ALT) indicator is on will cancel all
currently activated alarms at the same time.

J

Data Ports (DATA IN, OUT)
Exchanges control data with the WJ-SX550B Matrix
Switcher in a system.

K

This switch enables termination of the controller’s data
port.

L

This switch is used to identify the unit number of the
System Controller in multiple system controller applica-
tions. Up to eight controllers can be installed in a sys-
tem.

:

These switches are used to set the mode of the System
Controller connected to the Matrix Switcher. Set the
switches as shown below.

a

This switch is used to turn the WV-CU550B system con-
troller power on and off.

s

Normal Mode

CAM-P Mode

MODE

ON 1

2

3

4

MODE

ON 1

2

3

4