Read Panasonic WV-CP460 / WV-CP464 Service Manual online
WV-CP460 Series
– 8 –
6.4. Burst Level Adjustment
Menu:
6.4. BURST LEVEL
Test Point:
CN2 (Video Output Connector)
I/F Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Connector.
Adjust data with the ARROW keys so that the data
becomes same value of adjustment step 6.2.
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Connector.
Adjust data with the ARROW keys so that the data
becomes same value of adjustment step 6.2.
300
±
10 mV
Fig. 5-5
M
G
Y
L
B
G
C
Y
dG
10
°
0
°
10
°
dø
100%
75%
R
V
U
20%
20%
dG
135
±
1
°
M
G
Y
L
B
G
C
Y
dG
10
°
0
°
10
°
dø
100%
75%
R
V
U
20%
20%
dG
90
±
2
°
NTSC mode
PAL mode
Fig. 5-6
Select the item "6.1 BURST LEVEL" with the ROLL DOWN
key and press the ENTER key.
key and press the ENTER key.
6.1. Burst Level Adjustment
Menu:
6.1. BURST LEVEL
Test Point:
CN2 (Video Output Connector)
I/F Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Connector.
Adjust data with the ARROW keys so that the data
becomes +
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Connector.
Adjust data with the ARROW keys so that the data
becomes +
α
from noted data.
Press the ENTER key for next adjustment
6.2. Burst Level Adjustment
Menu:
6.2. BURST LEVEL
Test Point:
CN2 (Video Output Connector)
I/F Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Connector.
Adjust data with the ARROW keys so that the data
becomes –
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Connector.
Adjust data with the ARROW keys so that the data
becomes –
α
from noted data.
Press the ENTER key for next adjustment.
6.3. Burst Level Adjustment
Menu:
6.3. BURST LEVEL
Test Point:
CN2 (Video Output Connector)
I/F Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Connector.
Adjust data with the ARROW keys so that the data
becomes –
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Connector.
Adjust data with the ARROW keys so that the data
becomes –
α
from noted data.
Press the ENTER key for next adjustment.
6.4. Burst Level Adjustment
Menu:
6.4. BURST LEVEL
Test Point:
CN2 (Video Output Connector)
I/F Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Connector.
Adjust data with the ARROW keys so that the data
becomes +
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Connector.
Adjust data with the ARROW keys so that the data
becomes +
α
from noted data.
Press the ENTER key and ROLL DOWN Key to confirm
Burst Level, Phase and Red Vector position within the
specification as shown in Fig. 5-5, 5-6 , 5-7 and Table 5-2.
Burst Level, Phase and Red Vector position within the
specification as shown in Fig. 5-5, 5-6 , 5-7 and Table 5-2.
Table 5-46
Phase
Gain
Red
108
±
2
°
220
±
5 %
Yellow
165
±
5
°
100
±
5 %
Fig. 5-7
Table 5-2
Repeat adjustment from 6.1 to 6.4 until Burst Level,
Phase and Red Vector position are adjusted to proper
position.
Press the ENTER key for next adjustment.
Phase and Red Vector position are adjusted to proper
position.
Press the ENTER key for next adjustment.
cy
g
M
G
Y
L
yl
B
b
G
C
Y
dG
10
°
0
°
10
°
dø
100%
75%
R
V
U
mg
r
20%
20%
dG
Click on the first or last page to see other WV-CP460 / WV-CP464 service manuals if exist.