Read Panasonic WV-CP250 / WV-CP254E Service Manual online
2-4
4.2. Adjustment Procedure-2
(E.V.R. Adjustment)
8
Insert new disk containing the E.V.R. Adjustment pro-
gram into IBM PC/AT and turn on the Power Switch of
IBM PC/AT.
gram into IBM PC/AT and turn on the Power Switch of
IBM PC/AT.
8
When starting an adjustment, at the prompt, type LADJ2
CP250E and press the ENTER key, an initial menu will be
displayed in Table 4-1.
CP250E and press the ENTER key, an initial menu will be
displayed in Table 4-1.
Table 4-1
8
Press the SAVE (F5) key of the Computer, then the
Computer will ask you for the file name.
Computer will ask you for the file name.
8
Type xxxxxxxx.EVR. Give an appropriate file name for
xxxxxxxx within 8 letters, but do not use CP250E.
xxxxxxxx within 8 letters, but do not use CP250E.
8
Press the ENTER key.
8
This saving procedure is recommended to keep the cur-
rent adjustment status of the Camera.
rent adjustment status of the Camera.
8
Press the LOAD (F1) key and type CP250E.EVR and
press the ENTER key for presetting adjustment of the
Camera.
press the ENTER key for presetting adjustment of the
Camera.
8
Press the ENTER key to start adjustment.
4. Adjustment Procedure
8
The Location of test point refer to the WIRING DIAGRAM
on page 3-1.
on page 3-1.
4.1. Adjustment Procedure-1
(1). Line Lock VCO Adjustment
Test Point:
TP1 (LL VCO)
Main Board
Adjust:
L8 (LL VCO)
Sensor Board
8
Move the rear SW to the LL position, and make a line
lock.
lock.
8
Connect the Digital Voltmeter to TP1.
8
Adjust L8 so that the voltage becomes 1.65 V ± 0.35 V.
8
Return the rear SW to the INT position.
(2). Flange-back Adjustment
Test Point:
Video Output Connector
Adjust:
Focus lock knob
8
Referrint to Fig. 4-1, loosen the Focus lock knob.
8
Adjust the Focus lock knob to obtain a focused point
while watching the monitor screen.
while watching the monitor screen.
8
Tigheten the Focus lock knob.
Fig. 4-1
WV
-
CP250
CP250
ALC Lens
Focus lock
knob
knob
Loosen
Tighten
PANASONIC REMOTE EVR ADJUSTMENT SYSTEM (C) MCI Co. CCTV PRODUCT:CP250EEPROM:0
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
MENU
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
Page (1/1)
✽ ✽ ✽ ✽ ✽
PAL
1. FSC ADJUSTMENT
7.2.a. 5100K R-GAIN
3. ALC LEVEL
7.2.b. 5100K B-GAIN
4. AGC OFF GAIN
8. HIGH LIGHT CHROMA CLIP
5.1.a. OB LEVEL (LOW)
5.1.b. OB LEVEL (HIGH)
5.2. VIDEO OUT GAIN
5.3. OB CONFIRM
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.0.a. 3200K R-WB SETTING
7.0.b. 3200K B-WB SETTING
7.1.a. 3200K R-GAIN
7.1.b. 3200K B-GAIN
7.1.c. 3200K R-PHASE
7.1.d. 3200K B-PHASE
5.1.b. OB LEVEL (HIGH)
5.2. VIDEO OUT GAIN
5.3. OB CONFIRM
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.0.a. 3200K R-WB SETTING
7.0.b. 3200K B-WB SETTING
7.1.a. 3200K R-GAIN
7.1.b. 3200K B-GAIN
7.1.c. 3200K R-PHASE
7.1.d. 3200K B-PHASE
<CONTENTS> CN1 - 2PIN [CCD] 14.18750 MHz + - 40 Hz
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
LOAD (F1) QUIT (F3) SAVE (F5)
Click on the first or last page to see other WV-CP250 / WV-CP254E service manuals if exist.