Read Panasonic WV-CF224E Service Manual online
2-4
PANASONIC REMOTE EVR ADJUSTMENT SYSTEM (C) MCI Co. CCTV PRODUCT:CF224EEPROM:0
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
MENU
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
Page (1/1)
✽ ✽ ✽ ✽ ✽
PAL
1. FSC ADJUSTMENT
3. ALC LEVEL
4. AGC OFF GAIN
5.1. OB LEVEL
5.2. VIDEO OUT GAIN
5.3. OB CONFIRM
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.1. 3200K R GAIN
7.2. 3200K B GAIN
7.3. 3200K PHASE
7.5. COLOUR CENTER POINT ADJUSTMENT
8.1. ATW CONFIRM
8.2. HI LIGHT CHROMA CLIP
<CONTENTS> IC5 - 3PIN [CCD] 28.3750 MHz + - 40 Hz
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
3. ALC LEVEL
4. AGC OFF GAIN
5.1. OB LEVEL
5.2. VIDEO OUT GAIN
5.3. OB CONFIRM
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.1. 3200K R GAIN
7.2. 3200K B GAIN
7.3. 3200K PHASE
7.5. COLOUR CENTER POINT ADJUSTMENT
8.1. ATW CONFIRM
8.2. HI LIGHT CHROMA CLIP
<CONTENTS> IC5 - 3PIN [CCD] 28.3750 MHz + - 40 Hz
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
LOAD (F1) QUIT (F3) SAVE (F5)
Table 4-1
8
Press the SAVE (F5) key of the Computer, then the
Computer will ask you for the file name.
Computer will ask you for the file name.
8
Type xxxxxxxx.EVR. Give an appropriate file name for
xxxxxxxx within 8 letters, but do not use CF224E.
xxxxxxxx within 8 letters, but do not use CF224E.
8
Press the ENTER key.
8
This saving procedure is recommended to keep the cur-
rent adjustment status of the Camera.
rent adjustment status of the Camera.
8
Press the LOAD (F1) key and type CF224E.EVR and
press the ENTER key for presetting adjustment of the
Camera.
press the ENTER key for presetting adjustment of the
Camera.
8
Press the ENTER key to start adjustment.
4.2. Adjustment Procedure-2
(E.V.R. Adjustment)
8
Insert new disk containing the E.V.R. Adjustment pro-
gram into IBM PC/AT and turn on the Power Switch of
IBM PC/AT.
gram into IBM PC/AT and turn on the Power Switch of
IBM PC/AT.
8
When starting an adjustment, at the prompt, type LADJ
CF224E and press the ENTER key, an initial menu will be
displayed in Table 4-1.
CF224E and press the ENTER key, an initial menu will be
displayed in Table 4-1.
4. Adjustment Procedure
8
Refer to the WIRING DIAGRAM on page 3-1.
4.1. Adjustment Procedure-1
(1). Line Lock VCO Adjustment
Test Point:
TP1 (LL VCO)
Main Board
Adjust:
L301 (LL VCO)
Sensor Board
8
Set the Synchronization Mode Selector (on the SW Board
SW1) to LL position.
SW1) to LL position.
8
Connect the Digital Voltmeter to TP1.
8
Adjust L301 so that the voltage becomes 1.65 V ± 0.35 V.
8
Return the Synchronization Mode Selector (on the SW
Board SW1) to INT position.
Board SW1) to INT position.
(2). Flange-back Adjustment
Test Point:
Video Output Connector
Adjust:
Flange-back Adjusting Cam
8
Referring to Fig. 4-1, loosen the Zoom Lock Screw at the
tip of the Zoom Lever.
tip of the Zoom Lever.
8
Move the Zoom Lever to TELE side fully.
8
Loosen the Focus Lock Screw at the tip of the Focus
Lever.
Lever.
8
Move the Focus Lever to FAR side fully.
8
Set the Radiation Chart.
8
Aim the Camera at the Radiation Chart 10m away.
8
Loosen the Flange-back Lock Screw that secures the
Flange-back Adjusting Cam.
Flange-back Adjusting Cam.
8
Adjust the Flange-back Adjusting Cam to obtain best
focal point.
focal point.
Focus Lever
(Focus Lock Screw)
(Focus Lock Screw)
Zoom Lever
(Zoom Lock Screw)
(Zoom Lock Screw)
Flange-back
Adjusting Cam
Adjusting Cam
Flange-back
Lock Screw
Lock Screw
Fig. 4-1
8
Move the Zoom Lever to WIDE side fully.
8
Confirm that the focal point can be obtained by moving
the Focus Lever.
the Focus Lever.
8
Tighten the Flange-back Lock Screw that secure the
Flange-back Adjusting Cam carefully.
Flange-back Adjusting Cam carefully.
8
Tighten the Zoom Lock Screw at the tip of the Zoom
Lever carefully.
Lever carefully.
8
Tighten the Focus Lock Screw at the tip of the Focus
Lever carefully.
Lever carefully.
NEAR
FAR
WIDE
TELE
Click on the first or last page to see other WV-CF224E service manuals if exist.