Read Panasonic SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN Service Manual online
nInput sensitivity/Input impedance
PHONO (TRIM center)
2.5mV/47k
Ω
LINE (TRIM center)
250mV/10k
Ω
EFFECT RETURN
250mV/47k
Ω
MIC
0.7mV/1k
Ω
nRated output voltage/Output impedance
MASTER 1, 2 (RCA)
1V/600
Ω
MASTER 1 (XLR)
1V/600
Ω
MONITOR
1V/1k
Ω
REC OUT
250mV/1k
Ω
EFFECT SEND
250mV/1k
Ω
nHeadphone output
30mW/32
Ω
nFrequency response
MASTER 1, 2
20Hz to 20,000Hz
REC OUT
20Hz to 20,000Hz
EFFECT RETURN
20Hz to 20,000Hz
MIC
20Hz to 20,000Hz
nDigital audio input
Coaxial digital input
Compatible sampling rate
48kHz/44.1kHz/32kHz (PCM)
nDigital audio output
Coaxial digital output
2004
SH-MZ1200PP
SH-MZ1200EB
SH-MZ1200EG
SH-MZ1200EP
SH-MZ1200GN
SH-MZ1200EB
SH-MZ1200EG
SH-MZ1200EP
SH-MZ1200GN
Colour
K............Black Type
S............Silver Type
Sampling rate
44.1kHz (PCM)
nEqualizer characteristics
CD/LINE/PHONO
LOW
+12dB, -24dB (50Hz)
MID
+12dB, -24dB (1kHz)
HIGH
+12dB, -24dB (10kHz)
MIC
LOW
+12dB, -24dB (100Hz)
HIGH
+12dB, -24dB (10kHz)
nGeneral
Power supply
AC120V, 60Hz
(PP area)
AC230-240V, 50Hz
(EB,EG,EP,GN areas)
Power consumption
35W
Dimensions (W×H×D)
300mm × 103mm × 330mm
(11-26/32” × 4-1/16” × 13”)
Mass
5.3kg
(11.7lb.)
Note:
Specificationsare subject to change without notice.
Mass and dimensions are approximate.
Specificationsare subject to change without notice.
Mass and dimensions are approximate.
DJ Mixer
Specification
ORDER NO. AD0407060C0
A2
1
Safety Precaution
3
2
Caution for AC Mains Lead
4
3
Accessories
5
4
Component Part Name
6
5
Fader Replacement Instructions
8
6
Operation Checks and Component Replacement Procedures
9
6.1.
Checking for the output P.C.B., monitor P.C.B., sub
P.C.B., headphones P.C.B. and front sw P.C.B.
9
6.2.
Checking for the power transformer P.C.B.
11
6.3.
Checking for the input P.C.B. and sub P.C.B.
12
6.4.
Checking for the EQ P.C.B. and LED P.C.B.
13
6.5.
Removal of each P.C.B.
14
7
Schematic Diagram
17
7.1.
Schematic Diagram Notes
17
7.2.
Schematic Diagram
19
8
Printed Circuit Board Diagram
39
9
Block Diagram
45
10 Wiring Connection Diagram
49
11 Type Illustration of IC
痴, Transistors and Diodes
51
12 Repracement Parts List
52
13 Cabinet Parts Location
63
14 Packaging
65
CONTENTS
Page
Page
2
SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN
1 Safety Precaution
(This “Safety Precaution” is applied only in U.S.A.)
1. Before servicing, unplug the power cord to prevent an electric shock.
2. When replacing parts, use only manufacturer’s recommended components for safety.
3. Check the condition of the power cord. Replace if wear or damage is evident.
4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.
5. Before returning the serviced equipment to the customer, be sure to make the following insulation resistance test to prevent the
customer from being exposed to a shock hazard.
nInsulation Resistance Test
1. Unplug the power cord and short the two prongs of the plug with a jumper wire.
2. Turn on the power switch.
3. Measure the resistance value with ohmmeter between the jumper AC plug and each exposed metal cabinet part, such as screw
heads, control shafts, handle brackets, etc. Equipment with antenna terminals should read between 3M
Ω and 5.2MΩ to
allexposedparts. (Fig. A) Equipment without antenna terminals should read approximately infinity to all exposed parts. (Fig. B)
*Note: Some exposed partsmay beisolated from the chassis by design. These will read infinity.
*Note: Some exposed partsmay beisolated from the chassis by design. These will read infinity.
(Fig. A)
(Fig. B)
4. If the measurement is outside the specified limits, there is a possibility of a shock hazard. The equipment should be repaired
and rechecked before it is returned to the customer.
3
SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN
2 Caution for AC Mains Lead
4
SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN