Read Panasonic SC-HC10EB / SC-HC10EG / SC-HC10EP Service Manual online
5
1.3.
Before Repair and Adjustment
Disconnect AC power, discharge unit AC Capacitors as such C702, C710, C725, C727, C728 and C731 through a 10W, 1W resistor
to ground.
Caution : DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
to ground.
Caution : DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
• Current consumption at AC 220V to 240V, at 50Hz in NO SIGNAL mode (at volume min in FM Tuner mode) should be ~250 mA.
1.4.
Caution For Fuse Replacement
1.5.
Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
• No sound is heard when the power is turned on.
• Sound stops during a performance.
• Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
"shorted", or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
"shorted", or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
1.6.
Safety Part Information
Safety Parts List:
There are special components used in this equipment which are important for safety.
These parts are marked by in the Schematic Diagrams, Exploded View & Replacement Parts List. It is essential that these
critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the
original design without permission of manufacturer.
These parts are marked by in the Schematic Diagrams, Exploded View & Replacement Parts List. It is essential that these
critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the
original design without permission of manufacturer.
Table 1
Safety
Ref. No.
Part No.
Part Name & Description
Remarks
16
RFKHHC10EBK
REAR CABINET ASS’Y
EB/EG
16
RFKHHC10EPK
REAR CABINET ASS’Y
EP
401
RAE0165T-V
TRAVERSE UNIT
A2
K2CQ2CA00007
AC CORD
EG/EP
A2
K2CZ3YY00005
AC CORD
EB
A3
RQTX1043-D
O/I BOOK (Ge/It/Fr/Sp/Du/Da/Sw)
EG
A3
RQTX1045-B
O/I BOOK (En)
EB
A3
RQTX1046-E
O/I BOOK (En/Po/Cz/Ru/Ur)
EP
C702
F0CAF104A105
0.1uF
C710
F1BAF1020020
1000pF
C725
F0CAF104A105
0.1uF
C727
F1BAF1020020
1000pF
C728
F1BAF1020020
1000pF
C731
F1B3A221A027
220pF 1000V
F751
K5D162BK0005
FUSE
L702
G0B453G00003
LINE FILTER
L703
G0B9R5K00007
LINE FILTER
P751
K2AA2B000017
AC INLET
PC701
B3PBA0000402
PHOTO COUPLER
PCB3
REPX0818BA
SMPS P.C.B.
T701
ETS25BF116AD
TRANSFORMER
TH701
D4CAA5R10001
THERMISTOR
TH702
D4CC11040013
THERMISTOR
Z752
ERZV10V511CS
ZNR
Click on the first or last page to see other SC-HC10EB / SC-HC10EG / SC-HC10EP service manuals if exist.