Read Panasonic CS-BE25TKE-1 / CS-BE35TKE-1 / CS-DE25TKE-1 / CS-DE35TKE-1 / CU-BE25TKE-1 / CU-BE35TKE-1 / CU-DE25TKE-1 / CU-DE35TKE-1 Service Manual online
CS-BE35TKE-1
CS-DE25TKE-1
CS-DE35TKE-1
CU-BE35TKE-1
CU-DE25TKE-1
CU-DE35TKE-1
Russia
Belarus
with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the original design without permission of
manufacturer.
Area of Dry Mode) ...................................... 40
Operation .................................................... 44
Operation .................................................... 45
Air Conditioner and Pressure and Electric
Current ........................................................53
Cross Flow Fan and Indoor Fan Motor
Removal Procedures ..................................85
Procedure ...................................................90
Characteristic ..............................................94
Characteristic ..............................................98
List .................................................................. 103
and the seriousness is classified by the following indications.
leakage, electrical shock or fire.
leakage, fire or electrical shock.
done, the set will drop and cause injury.
outlet must be used. If electrical circuit capacity is not enough or defect found in electrical work, it will cause electrical shock or fire.
Otherwise, it may cause electrical shock and fire in case equipment breakdown or insulation breakdown.
instruction CONNECT THE CABLE TO THE INDOOR UNIT and connect tightly for indoor / outdoor connection. Clamp the cable so that
no external force will be acted on the terminal. If connecting or fixing is not perfect, it will cause heat up or fire at the connection.
cause heat-up or fire at the connection point of terminal, fire or electrical shock.
cycle (piping). (Mixing of air etc. will cause abnormal high pressure in refrigeration cycle and result in explosion, injury etc.).
up to outdoor unit and cross over the handrail and causing accident.
telephone. Otherwise, it may cause electric shock in case equipment breakdown or insulation breakdown.
with other electrical appliances. Poor contact, poor insulation or over current will cause electrical shock or fire.
flare may break and cause refrigerant gas leakage.
flare nut and tools may cause abnormally high pressure in the refrigerant cycle (piping), and possibly result in explosion
and injury.
piping and valves at opened condition will caused suck-in of air, abnormal high pressure in refrigeration cycle and result in explosion,
injury etc).
operating and valves are opened will cause suck-in of air, abnormal high pressure in refrigeration cycle and result in explosion, injury
etc.)
contacts with fire.
of the unit, it may cause fire.
furniture.
may break and cause refrigerant gas leakage.
use a high temperature solder iron. In case of the soldering iron with temperature control, please set it to 700 ± 20°F (370 ± 10°C).
Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
Use power supply cord 3 × 1.5 mm² (1.0 ~ 1.5HP) type designation 60245 IEC 57 or heavier cord.
Connect the power supply cord of the air conditioner to the mains using one of the following method.
Power supply point should be in easily accessible place for power disconnection in case of emergency.
In some countries, permanent connection of this air conditioner to the power supply is prohibited.
1) Power supply connection to the receptacle using power plug.
Use an approved 15/16A (1.0 ~ 1.5HP) power plug with earth pin for the connection to the socket.
2) Power supply connection to a circuit breaker for the permanent connection.
Use an approved 16A (1.0 ~ 1.5HP) circuit breaker for the permanent connection. It must be a double pole switch with a minimum
3.0 mm contact gap.
Take care of the liquid refrigerant, it may cause frostbite.
If you are required to handle sharp parts during installation or servicing, please wear hand glove.
Sharp parts may cause injury.