Read LG 60PF95-ZA (CHASSIS:PD75A) Service Manual online
- 9 -
10. Adjustment of Component
10-1. Required Equipment
(1) Remote controller for adjustment.
(2) MSPG-925FS Pattern Generator. (Which has 720p/50Hz
(2) MSPG-925FS Pattern Generator. (Which has 720p/50Hz
YPbPr output Pattern shown in Fig.3)
-> Model : 215 / Pattern : 65
-> Model : 215 / Pattern : 65
10-2. Method of Auto Component Color Balance
(1) Input the Component 720p/50Hz 7 Color Bar(MSPG-
925FS model:215, pattern:65) signal into Component.
(2) Set the PSM to Dynamic mode in the Picture menu.
(3) Press IN-START key on R/C for adjustment.
(4) Press the
G
(Vol. +) key to operate the set, then it becomes
automatically.
(5) After downloading complete, the ‘OK’ word appears.
(6) Auto-RGB OK means the adjustment is completed.
(6) Auto-RGB OK means the adjustment is completed.
11. Adjustment of RGB
11-1. Required Equipment
(1) Remote controller for adjustment.
(2) MSPG-925FS Pattern Generator ( Which has XGA
(2) MSPG-925FS Pattern Generator ( Which has XGA
[1024*768] 60Hz 1/2 black & white pattern shown in Fig.4 )
11-2. Method of Auto RGB Color Balance
(1) Input the PC 1024x768 @ 60Hz 1/2 black & white pattern
(MSPG-925FS, Model:3, Pattern:65) into RGB.
(using D-sub to D-sub cable)
(using D-sub to D-sub cable)
(2) Set the PSM to Dynamic mode in the Picture menu.
(3) Press IN-START key on R/C for adjustment.
(4) Press the
G
(Vol. +) key to operate the set, then it becomes
automatically.
(5) After downloading complete, the ‘OK’ word appears.
(6) Auto-RGB OK means the adjustment is completed.
(6) Auto-RGB OK means the adjustment is completed.
12. Adjustment of White Balance
12-1. Required Equipment
(1) Color Analyzer.(CS-100, CA-100+(CH 10), CA-210(CH 10))
* Please adjust CA-210, CA-100+ by CS-1000 before
* Please adjust CA-210, CA-100+ by CS-1000 before
measuring.
W
Color temperature standards according to CSM and Module.
W
White balance adjustment coordinate and color temperature.
* PC(for communication through RS-232C)
-> UART Baud rate : 115200 bps
12-2. Connection Picture of the Measuring
Instrument(On Automatic control)
(1) Inside PATTERN is used when W/B is controlled. Connect
to auto controller or push control R/C IN-START -> Enter
the mode of White-Balance, the pattern will come out.
the mode of White-Balance, the pattern will come out.
12-3. Auto-control interface and directions
(1) Adjust in the place where the influx of light like floodlight
around is blocked.(illumination is less than 10ux)
(2) Measure and adjust after sticking the Color Analyzer(CA-
100+, CA210) to the side of the module.
(3) Aging time : keep white pattern using inside pattern.
(Fig.3)
(Fig.4)
(Fig.5) Auto AV(CVBS) Color Balance Test Pattern
Full White Pattern
RS-232C Communication
CA-210
Color
ANALYZER
TYPE : CA-210
PLASMA
Remark
11000K
9300K
6500K
Cool
Normal
Warm
CSM
CS-1000
CA-100(CH 10)
CA-210(CH 10)
0.276 ± 0.002
0.283 ± 0.002
0.000
0.276 ± 0.002
0.283 ± 0.002
0.000
0.276
0.283
0.000
x
y
uv
Cool
CS-1000
CA-100(CH 10)
CA-210(CH 10)
0.285 ± 0.002
0.293 ± 0.002
0.000
0.285 ± 0.002
0.293 ± 0.002
0.000
0.285
0.293
0.000
x
y
uv
Medium
CS-1000
CA-100(CH 10)
CA-210(CH 10)
0.313 ± 0.002
0.329 ± 0.002
0.003
0.313 ± 0.002
0.329 ± 0.002
0.003
0.313
0.329
0.003
x
y
uv
Warm
Click on the first or last page to see other 60PF95-ZA (CHASSIS:PD75A) service manuals if exist.