Read LG 50PT85-ZB (CHASSIS:PD74A) Service Manual online
- 11 -
V
Auto adjustment Map(RS-232C)
12-3. Auto-control interface and directions
(1) Adjust in the place where the influx of light like floodlight
around is blocked.(illumination is less than 10ux)
(2) Measure and adjust after sticking the Color Analyzer(CA-
100+, CA-210) to the side of the module.
(3) Aging time
- After aging start, keep the power on(no suspension of
power supply) and heat-run over 15minutes.
- Keep white pattern using inside pattern.
13. Adjustment of White Balance
(Manual white Balance)
V
One of R Gain/ G Gain/ B Gain should be kept on 80, and
others are controlled lowering from 80
(1) press “power on” of the control R/C, set heat run to white
by pressing
G
and heat run over 15 minutes.
(Set: RS-232 Host: PC, Baud Rate: 115200bps,
Download: Cortez)
2) Zero Calibrate CA-100+, and when controlling, stick the
sensor to the center of PDP module surface.
3) Double click In-start key on Controlling R/C and get in
‘white balance’.
4) Set test-pattern on and display inside pattern. Control is
carried out on three color temperature, COOL, MEDIUM,
WARM. (Control is carried out three times,)
WARM. (Control is carried out three times,)
5) When the R/G/B GAIN is 80 on OSD, it is the FULL
DYNAMIC Range of the Module. In order to control white
balance without the saturation of FULL DYNAMIC Range
and DATA, one of R Gain / G Gain / B Gain should be kept
on 80, and other two is controlled lowering from 80.
balance without the saturation of FULL DYNAMIC Range
and DATA, one of R Gain / G Gain / B Gain should be kept
on 80, and other two is controlled lowering from 80.
* Color Temperature: Cool, Medium, Warm
(1) When R GAIN is set to 80
- Control G GAIN and B GAIN by lowering from 80.
(2) When B GAIN is set to 80
- Control R GAIN and G GAIN by lowering from 80.
(3) When G GAIN is set to 80
- Control R GAIN and B GAIN by lowering from 80.
- Control R GAIN and B GAIN by lowering from 80.
One of R Gain / G Gain / B Gain should be kept on 80, and
adjust other two lower than 80.
(When R/G/B GAIN are all 80, it is the FULL DYNAMIC
Range of Module).
adjust other two lower than 80.
(When R/G/B GAIN are all 80, it is the FULL DYNAMIC
Range of Module).
14. Default Value in Adjustment mode
14-1. Auto Color Balance
14-2. Write Balance
(Fig.12) Default Value on OSD
<Component>
<RGB>
(Fig.13) Default Value on OSD
Type
PD74A
Baud Rate
Data bit
Stop bit
Parity
115200
8
1
None
Protocol
Index
Cmd 1 Cmd 2
Data Min Value
Max Value
Setting
R-Gain_Normal
j
a
00(00)
128(80)
G-Gain_Normal
j
b
00(00)
128(80)
B-Gain_Normal
j
c
00(00)
128(80)
R-Gain_Warm
j
d
00(00)
128(80)
G-Gain_Warm
j
e
00(00)
128(80)
B-Gain_Warm
j
f00(00)
128(80)
R-Gain_Cool
j
g
00(00)
128(80)
G-Gain_Cool
j
h
00(00)
128(80)
B-Gain_Cool
j
i
00(00)
128(80)
R-Offset_Normal
l
j
00(00)
128(80)
G-Offset_Normal
l
k
00(00)
128(80)
B-Offset_Normal
l
l
00(00)
128(80)
R-Offset_Warm
l
m
00(00)
128(80)
G-Offset_Warm
l
n
00(00)
128(80)
B-Offset_Warm
l
o
00(00)
128(80)
R-Offset_Cool
l
p
00(00)
128(80)
G-Offset_Cool
l
q
00(00)
128(80)
B-Offset_Cool
l
r
00(00)
128(80)
w
b
00
W/B adjustment Start
w
b
10
w
b
ff
W/B adjustment end
Click on the first or last page to see other 50PT85-ZB (CHASSIS:PD74A) service manuals if exist.