32LD660, 32LD665H (CHASSIS:LA05C) - LG TV Service Manual (repair manual). Page 14

- 14 -

(1) Overview

• W/B adj. Objective & How-it-works

- Objective: To reduce each Panel’s W/B deviation
- How-it-works: When R/G/B gain in the OSD is at 192, it

means the panel is at its Full Dynamic
Range. In order to prevent saturation of
Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is
lowered to find the desired value.   

- Adj. condition : normal temperature

1) Surrounding Temperature: 25±5ºC
2) Warm-up time: About 5 Min
3) Surrounding Humidity: 20% ~ 80%

(2) Equipment

1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12)
2) Adj. Computer(During auto adj., RS-232C protocol is

needed)

3) Adjust Remocon
4) Video Signal Generator MSPG-925F 720p/216-Gray

(Model:217, Pattern:78)

-> Only when internal pattern is not available

• Color Analyzer Matrix should be calibrated using CS-1000

(3) Equipment connection MAP

(4) Adj. Command (Protocol)

1) RS-232C Command used during auto-adj.

Ex) wb 00 00   ->  Begin white balance auto-adj.

wb 00 10   ->  Gain adj.
ja 00 ff   ->  Adj. data
jb 00 c0
...

...

wb 00 1f   -> Gain adj. complete
*(wb 00 20(start), wb 00 2f(end)) -> Off-set adj.
wb 00 ff   -> End white balance auto adj.

2) Adjustment Map
Applied Model : LA02B Chassis ALL MODELS 

(5) Auto adj. method

1) Set TV in adj. mode using POWER ON key
2) Zero calibrate probe then place it on the center of the

Display

3) Connect Cable(RS-232C)
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sing), check adj. status pre

mode (Warm, Medium, Cool)

6) Remove probe and RS-232C cable to complete adj.

* W/B Adj. must begin as start command “wb 00 00” , and

finish as end command “wb 00 ff”, and Adj. offset if need 

(6) Manual adj. method

1) Set TV in Adj. mode using POWER ON
2) Zero Calibrate the probe of Color Analyzer, then place

it on the center of LCD module within 10cm of the
surface..

3) Press ADJ key -> EZ adjust using adj. R/C > 6. White-

Balance then press the cursor to the right (KEY

G

).

(When KEY(

G

) is pressed 216 Gray internal pattern

will be displayed)

4) One of R Gain / G Gain / B Gain should be fixed at

192, and the rest will be lowered to meet the desired
value.

5) Adj. is performed in COOL, MEDIUM, WARM 3 modes

of color temperature.

- If internal pattern is not available, use RF input. In EZ

Adj. menu 6.White Balance, you can select one of 2
Test-pattern: ON, OFF. Default is inner(ON). By
selecting OFF, you can adjust using RF signal in 216
Gray pattern.

Co lo r An alyzer

 

Co m p ut er

 

Pat t ern Gen erat o r

 

RS -232C 

RS -232C 

RS -232C 

Probe

Signal Source

* If TV internal pattern is used, not needed

Connection Diagram of Automatic Adjustment

RS-232C COMMAND

Meaning

[CMD

ID

DATA]

wb

00

00

Begin White Balance adj.

wb

00

ff

ITEM

Command

Data Range

Default

(Hex.)

(Decimal)

Cmd 1

Cmd 2

Min

Max

Cool

R-Gain

j

g

00

C0

G-Gain

j

h

00

C0

B-Gain

j

i

00

C0

R-Cut

G-Cut

B-Cut

Medium

R-Gain

j

a

00

C0

G-Gain

j

b

00

C0

B-Gain

j

c

00

C0

R-Cut

G-Cut

B-Cut

Warm

R-Gain

j

d

00

C0

G-Gain

j

e

00

C0

B-Gain

j

f

00

C0

R-Cut

G-Cut