Read LG 32LC3D (CHASSIS:LT61A) Service Manual online
- 9 -
ADJUSTMENT INSTRUCTION
1. Application Range
This spec. sheet is applied to all of the LT61A chassis
manufactured at LG TV Plant all over the world.
manufactured at LG TV Plant all over the world.
2. Specification.
2.1 Because this is not a hot chassis, it is not necessary to
use an isolation transformer.
However, the use of isolation transformer will help to
protect test instruments.
protect test instruments.
2.2 Adjustment must be done in the correct sequence.
2.3 The adjustment must be performed at 25±5°C
2.3 The adjustment must be performed at 25±5°C
temperature and 65±10% relative humidity if there is no
specified designation.
specified designation.
2.4 The input voltage of the receiver must be kept between
100~220V, 50/60Hz.
2.5 Before adjustment, execute Heat-Run for 30 minutes at
RF no signal.
3. EDID
* Caution
* Use the proper signal cable for EDID Download
- Analog EDID : Pin3 exists
=> Caution: - Never connect HDMI & D-sub Cable at the
same time.
- Use the proper cables below for EDID Writing
3.1 Data
1. ANALOG(128 Bytes)
2. HDMI(256 Bytes)
4. ADC Calibration
=> Caution: - System control RS-232 Host should be "PC"
for adjustment.
4.1. Adjustment of RF/VIDEO/S-VIDEO
* Required Equipments
O
Remote controller for adjustment
O
MSPG-925F Pattern Generator (Which has Video Signal :
100% Color Bar Pattern shown in Fig. 1)
=> Model: 201 / Pattern : 33 (NTSC-M)
(1) Method of Auto RF/VIDEO/S-VIDEO Color Balance.
1) Input the Video Signal: 100% Color Bar signal into
VIDEO1
2) Set the EZ PICTURE to Optimum mode in the Picture
menu.
[Fig.1]
3) Press ADJ key on R/C for adjustment.
4) Press the G(Vol. +) key to operate the set, then it
becomes automatically.
5) Auto-RGB OK means the adjustment is completed.
4.2. Adjustment of Component.
* Required Equipments
O
Remote controller for adjustment
O
MSPG-925F Pattern Generator e Model: 217 / Pattern: 33
(Which has 720p YPbPr output Pattern shown in Fig. 2)
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
00 00 FF FF FF FF FF FF 00 1E 6D 00 00 01 01 01 01
10 00 10 01 03 68 52 2F 96 EA D9 B0 A3 57 49 9C 25
20 11 49 4B AF CE 00 31 4F 45 4F 61 4F 01 01 01 01
30 01 01 01 01 01 01 1B 21 50 A0 51 00 1E 30 48 88
40 35 00 BC 88 21 00 00 1C 4E 1F 00 80 51 00 1E 30
50 40 80 37 00 BC 88 21 00 00 18 00 00 00 FD 00 38
60 4B 1F 3D 09 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 33 37 4C 43 32 44 2D 44 41 0A 20 20 20 00 F6
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
00 00 FF FF FF FF FF FF 00 1E 6D 00 00 01 01 01 01
10 00 10 01 03 80 52 2F 96 EA D9 B0 A3 57 49 9C 25
20 11 49 4B A5 CE 00 31 4F 45 4F 61 4F 01 01 01 01
30 01 01 01 01 01 01 1B 21 50 A0 51 00 1E 30 48 88
40 35 00 BC 88 21 00 00 1C 4C 1F 00 90 51 00 1E 30
50 BB 88 97 00 A2 0B 32 00 00 1E 00 00 00 FC 00 33
60 37 4C 43 32 44 2D 44 41 0A 20 20 20 00 00 00 FD
70 00 38 4B 1F 3D 09 00 0A 20 20 20 20 20 20 01 76
80 02 03 1D 72 23 08 07 07 4A 85 04 03 02 01 14 13
90 12 11 00 83 01 00 00 65 03 0C 00 10 00 01 1D 80
A0 D0 72 1C 16 20 10 2C 25 80 C4 8E 21 00 00 9E 01
B0 1D 80 18 71 1C 16 20 58 2C 25 00 C4 8E 21 00 00
C0 9E 01 1D 00 BC 52 D0 1E 20 B8 28 55 40 C4 8E 21
D0 00 00 1E 01 1D 00 72 51 D0 1E 20 6E 28 55 00 C4
E0 8E 21 00 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96
F0 00 13 8E 21 00 00 18 00 00 00 00 00 00 00 00 1B
ADC
RF/VIDEO/S-VIDEO
Component
RGB
MSPG925F
VIDEO1
Model: 217(720P)
Model: 39
Model: 201 (NTSC-M)
Pattern: 33
(1024*768 60Hz)
Pattern: 33
*720P 100% Color Bar
Pattern: 33
*NTSC 100% Color Bar
*XGA 100% Color Bar
Click on the first or last page to see other 32LC3D (CHASSIS:LT61A) service manuals if exist.