Read JBL GTO-3EZ Service Manual online
PROBLEM
CAUSES AND SOLUTIONS
No sound (the amplifier’s
Power/ Protection LED is off):
Power/ Protection LED is off):
• Check that the amplifier’s +12V and GND connections have been properly
made.
• Check if the fuse on the +12V wire located near the battery is blown; if so,
replace it with an identical fuse.
• Check all amplifier fuses; if any are blown, replace them with identical fuses.
• If you are using the amplifier’s REM connection for turn-on, check that the
wire is properly connected to the audio system’s remote turn-on wire or to the
vehicle’s ACC power terminal.
vehicle’s ACC power terminal.
• If you are using the amplifier’s Auto Turn-On circuit for turn-on, check that the
amplifier’s Auto Turn-On switch (on the amplifier’s bottom panel) is set in the
“On” position.
“On” position.
No sound (the amplifier’s
Power/ Protection LED is
orange):
Power/ Protection LED is
orange):
• Check that all amplifier input and speaker connections have been properly
made.
• Check that the amplifier’s Gain controls are not turned all the way down.
• Check that the vehicle audio system’s source unit’s volume control is not
turned all the way down.
No sound (the amplifier’s
Power/ Protection LED is red):
Power/ Protection LED is red):
• Confirm that the vehicle’s electrical system is supplying between 9V and 16V
DC to the amplifier. If the supply voltage is outside of this range, correct the
condition before attempting to use the amplifier.
condition before attempting to use the amplifier.
• If the amplifier has overheated, wait until it has cooled down before attempting
to use it again.
• Disconnect all speakers from the amplifier and attempt to turn it on again:
– If the amplifier turns on (the Power/Protect LED is orange), there is a short
circuit in one or more of the speaker wires. Correct all short circuits before
reconnecting the speakers to the amplifier.
reconnecting the speakers to the amplifier.
– If the amplifier does not turn on (the Power/Protect LED is still red), contact
your authorized JBL dealer for assistance.
TROUBLESHOOTING
If your amplifier isn’t performing the way you think it should, check to see if the problem is covered in this section
before calling your dealer or contacting JBL customer service.
before calling your dealer or contacting JBL customer service.
Sound in the front/rear speakers
is distorted:
is distorted:
• If the amplifier channels’ Input Level switch is set in the “Low” position, change
the setting to “Hi1” and perform the Set the Gain procedure, on page 9, again
for those channels.
for those channels.
• Make sure amplifier’s Crossover Filter selector for the distorted channels is set
to HP.
• Set the distorted channels’ Crossover control to a higher setting.
• Check that the distortion is not originating from the vehicle audio system’s
source unit.
Sound in the subwoofer is
distorted:
distorted:
• If the amplifier Sub channel’s Input Level switch is set in the “Low” position,
change the setting to “Hi1” and perform the Set the Gain procedure, on page
9, again for those channels.
9, again for those channels.
• While listening to bass-heavy music, turn the Bass Boost control all the way
down, and then gradually increase it until the distortion begins to return.
Reduce the Bass Boost control setting slightly to eliminate the distortion and
leave it set there.
Reduce the Bass Boost control setting slightly to eliminate the distortion and
leave it set there.
• Check that the distortion is not originating from the vehicle audio system’s
source unit.
GTO-5EZ only: The vehicle audio
system’s source unit’s fader
control has no effect:
system’s source unit’s fader
control has no effect:
• Make sure that the amplifier’s Front/Rear Input Routing switch is set in the
“F&R” position.
The vehicle audio system’s
subwoofer volume control does
not control the subwoofer’s
volume:
subwoofer volume control does
not control the subwoofer’s
volume:
• Make sure that the amplifier’s Sub Input Routing switch is set in the “S”
position.
The amplifier’s Gain LEDs
constantly illuminate red while
the amplifier is operating:
constantly illuminate red while
the amplifier is operating:
• Set the amplifier’s Gain LEDs switch in the “Off” position.
GTO-3EZ
8
Click on the first or last page to see other GTO-3EZ service manuals if exist.