ON TOUR (serv.man4) - JBL Audio User Guide / Operation Manual. Page 7

Read JBL ON TOUR (serv.man4) User Guide / Operation Manual online

K
TRIM
FOLD
TRIM
Step 2.
Open battery compartment
by sliding button as shown.  Battery
door will open.  
Step 3.
Place (4) fresh AAA batteries
as shown.  Replace battery compart-
ment cover.  System will function with
AC power only or batteries.
Step 4.
Open protective cover by
sliding cover as shown. When the
cover is closed, the system will
power off.
Symptom
No sound from on tour
speaker system.
Possible problem
No power to system.
Power adapter plug not
inserted correctly.
Batteries are empty
No volume or low volume.
Input source is low
Solution
Ensure power supply is connected to live
power source and properly connected to
on tour. Please note: When on tour is pow-
ered, a green power LED should 
illuminate.
Replace/ Recharge batteries
Touch the volume “Up” (+) pad on the vol-
ume control to un-mute and/or increase
the system volume level.
Note: touching the volume “Down” (-) pad
lowers the system volume. Touching both
(+) and (-) volume control pads at the
same time will mute the system.
Increase the volume level on the audio
source device.
Troubleshooting
on tour specifications
Frequency range: 100Hz–20kHz
Power consumption: 6  W  maximum
Transducers: (1) 1-inch full range per channel
Amplifier output power: 3 Wrms per channel
Dimensions: 
6.75" (17.1 cm) long 
3.5" (8.9 cm) wide
1.5" (3.8 cm) tall
Weight: 1.1 pound = 0.5 kg
Battery
Size - AAA
Type - Alkaline, NiMh
DO NOT MIX BATTERY TYPES
DO NOT MIX CHARGED AND
PARTIALLY CHARGED
BATTERIES
BATTERIES WILL NOT
RECHARGE WHILE IN
ON TOUR
on tour
Easy Setup Guide
If you have any questions, or need further assistance, please visit www.JBL.com.
*These specifications are subject to change without notice.
6
Step 6. P
lug input cable into
on tour.  Plug input cable to audio
device.  Start audio device.
Step 5.
Connect wall adaptor to on
tour.  Connect adaptor to wall outlet.
CAUTION - Remove Adaptor from out-
let before installing or replacing batter-
ies.
Step 7.
Adjust  Volume using “+” to
increase and “-” to decrease.  Press
both to Mute the on tour Press either
button to Unmute.
Step 8.
Green LED indicates that
power is on.  Flashing Green LED
indicates no input signal.  Amber
LED will flash when batteries need
replacement.
Symptom
No Power.  Green LED is not on.
Green LED is Flashing and there is
No Sound.
Possible problem
Batteries are very low.
Wall Adaptor is not plugged into on
tour correctly.
Wall adaptor is not receiving AC
power.
There is no input signal
Input source is low
Solution
Replace batteries with fresh Akaline AAA or fully charged rechargable bat-
teries.
Check connection of wall adaptor.
Place wall adaptor in a known powered outlet.  Test outlet with a lamp or
other device.
Connect on tour  to known audio source.  Test the audio source with head-
phones.
Increase the volume level on the audio source device.
7
www.JBL.com
This product is intended to be supplied by a Listed Direct Plug-in Power Unit marked ‘Class 2 and Output rated 6 Vdc minimum 1.0A.
Step 1.
Unpack on tour, wall adaptor and
cable.  Read this instruction sheet completely.
Page of 19
Display

Click on the first or last page to see other ON TOUR (serv.man4) service manuals if exist.